BMW X5 Service Bulletins (2014)
396 manufacturer communications on file.
- October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149379Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
Associated Products (53)Associated Documents - October 1, 2014•Document ID: 10149377Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 631014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryAdaptive Headlight Malfunction. A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.
Associated Products (46)Associated Documents - October 1, 2014•Document ID: 10149376Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryLED Headlight Malfunction. 1. The LED headlight on one side malfunctions. 2. One headlight flickers on and off while driving (problem is sporadic). 3. The Check Control message indicates the parking light or driving light is defective. One or more of the following faults can be stored: 805980 Low-beam headlight defective 805981 High-beam headlight defective 8044BB Right-hand LED main light module (LHM2) implausible low-beam headlight function status 8044BA Left-hand LED main light module (LHM2) implausible low-beam headlight function status CAUSE The situation above is caused by a poor connection at the LED headlight connector or LED main light module.
Associated Products (11)Associated Documents - October 1, 2014•Document ID: 10149353Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 130114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149282Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 111414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryEngine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
Associated Products (93)Associated Documents - October 1, 2014•Document ID: 10057762Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH
- Mfr Comm. #:
- SI B65 13 13
- Date Added:
- June 24, 2015
- Manufacturer:
- BMW
SummaryBMW: SOME BMW MODELS CENTRAL INFORMATION DISPLAY (CID) ARE BLANK AND DISPLAY "NO SIGNAL". *TA
Associated Products (7)Associated Documents - October 1, 2014•Document ID: 10057567Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- SIB-63-10-14
- Date Added:
- June 10, 2015
- Manufacturer:
- BMW
SummaryBMW: SOME VEHICLES EXPERIENCING VARIOUS MESSAGE DISPLAYED REGARDING MALFUNCTION OF LED HEADLIGHT, WITH OPTIONS 0552 AND 0524. *PE
Associated Products (19)Associated Documents - October 1, 2014•Document ID: 10057566Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- SIB-63-09-14
- Date Added:
- June 10, 2015
- Manufacturer:
- BMW
SummaryBMW: SOME VEHICLES, WITH 552 OPTION, ARE EXPERIENCING A MALFUNCTION OF LED HEADLIGHT ON ONE WHERE IT FLICKERS ON AN DOFF DURING DRIVING AND THE CONTROL CHECK MESSAGE IS INDICATING DEFECTIVE DRIVING LIGHT OR PARKING LIGHT. *PE
Associated Products (29)Associated Documents - September 1, 2014•Document ID: 10148043Service Bulletin/Repair InstructionsPOWER TRAIN; EQUIPMENT
- Mfr Comm. #:
- 710114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"BMW centers must ensure Recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a Recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) Recall message. When a Recall Campaign is announced by BMW NA, centers must ensure that all Recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open Recall. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Voluntary Emissions Recall Campaign 14E-A01: Replace Emissions Label. Certain 2014 model year F15 vehicles produced from March 13, 2014 through April 12, 2014. These vehicles are equipped with an ""emissions"" label with incorrect information pertaining to the model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery."
Associated Products (2)Associated Documents - September 1, 2014•Document ID: 10148039Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"
Associated Products (40)Associated Documents - September 1, 2014•Document ID: 10148036Service Bulletin/Repair InstructionsENGINE; STRUCTURE
- Mfr Comm. #:
- 612314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"The Start/Stop Button Must Be Pressed Several Times to Stop Engine. To turn the engine off when it is running, the start/stop button must be pressed several times. This error does not affect starting of the engine. Body Domain Controller (BDC) application software error BDC fault ""8040A9 - Start-stop button SST: Incorrect operation (pushed at an angle)"" is stored."
Associated Products (4)Associated Documents - September 1, 2014•Document ID: 10148028Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY:DOOR
- Mfr Comm. #:
- 511614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDoor Opens to First Stage While Driving. The door opens to the first stage and the Check Control Message (CCM) is displayed. Front or rear door lock Bowden cable cover and the door lock
Associated Products (2)Associated Documents - September 1, 2014•Document ID: 10148025Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE
- Mfr Comm. #:
- 130314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Engine Soon Lamp (MIL) On with NOx Sensor Faults Stored. The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics
Associated Products (7)Associated Documents - September 1, 2014•Document ID: 10148022Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 122514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63T: Improvements to Bosch Spark Plug. Various engine performance symptoms could occur if the spark plug insulator becomes damaged: * The Service Engine Soon (MIL) may be on with rough running and misfire fault(s) stored. * Intermittent performance or rough running without a relevant DME fault stored. The spark plug insulator could be damaged in cases of combustion faults such as misfiring, ignition knock or super knocking conditions.
Associated Products (22)Associated Documents - September 1, 2014•Document ID: 10056719Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SIB-12-26-14
- Date Added:
- February 7, 2015
- Manufacturer:
- BMW
SummaryBMW: WITH DRIVETRAIN MALFUNCTION MESSAGE DISPLAYED AND SERVICE ENGINE SOON, ENGINE CAN GO INTO REDUCED POWER MODE, DUE TO ENGINE POSITION MANAGEMENT (EPM) UNFAVORABLE PARAMETERS IN DME SOFTWARE. *PE
Associated Products (29)Associated Documents - September 1, 2014•Document ID: 10056716Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR
- Mfr Comm. #:
- SIB-51-16-14
- Date Added:
- February 7, 2015
- Manufacturer:
- BMW
SummaryBMW: CHECK CONTROL MESSAGE (CCM) IS DISPLAYED, WHEN DOOR OPENS TO FIRST STAGE DUE TO REAR OR FRONT DOOR LOCK AND BOWDEN CABLE COVER AND DOOR LOCK WOULD NEED REPLACING, AS NEEDED. MODEL 2013-15 F15 (X5). *PE
Associated Products (3)Associated Documents - August 1, 2014•Document ID: 10148380Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCentral Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
Associated Products (68)Associated Documents - August 1, 2014•Document ID: 10148374Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 620314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHead-Up Display: Height Adjustment Not Stored. The height adjustment for the Head-up Display is not permanently stored in Personal Profiles for the remote control key used. When using a different remote control key, the height adjustment resets to the default value. Software error in the instrument cluster
Associated Products (2)Associated Documents - August 1, 2014•Document ID: 10148368Service Bulletin/Repair InstructionsSTRUCTURE:FRAME AND MEMBERS
- Mfr Comm. #:
- 511814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryWind Noises. The customer complains of wind noises from the exterior windows, exterior mirrors and/or A, B or C pillars. Seal fitment mainly on the exterior mirrors, doors and window seals
Associated Products (2)Associated Documents