BMW X2 Service Bulletins (2018)
109 manufacturer communications on file.
- May 1, 2020•Document ID: 10176370Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN; VISIBILITY
- Mfr Comm. #:
- B511318
- Date Added:
- June 15, 2020
- Manufacturer:
- BMW
SummaryLIN BUS FAULTS WITH EXTERIOR REARVIEW MIRROR GLASS DAMAGE: Any or all of these conditions may be present: A. The exterior rearview mirror glass is discolored or cracked B. The power windows and folding mirrors may not operate C. One or more of the following LIN bus faults are stored in the BDC (Body Domain Controller): D90C03 LIN bus master B: short circuit - BDC D90C04 LIN bus master B: No communication - BDC D90C05 LIN bus master B: Communication failed - BDC D90D07 Operating facility switch block (LIN): Missing LIN slave D90D0A exterior rearview mirror left (LIN bus): Absent LIN slave - BDC D90D0D exterior rearview mirror right (LIN bus): Absent LIN slave - BDC 804246 exterior rearview mirror left (LIN bus): Heating or electrochrome: faulty - BDC 804256 exterior rearview mirror right (LIN bus): Heating or electrochrome: faulty - BDC 804265 exterior mirror left or right: Excess temperature - BDC 804260 exterior mirror left or right: Overvoltage - BDC 804261 exterior mirror left or right: Undervoltage - BDC Faulty exterior rearview mirror electronics have created a short on the LIN bus damaging the mirror glass and causing functional errors in power window and exterior mirror operation.
Associated Products (8)Associated Documents - May 1, 2020•Document ID: 10176363Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B130420
- Date Added:
- June 15, 2020
- Manufacturer:
- BMW
SummaryTANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
Associated Products (140)Associated Documents - May 1, 2020•Document ID: 10176362Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- B122117
- Date Added:
- June 15, 2020
- Manufacturer:
- BMW
SummaryROUGH RUNNING IMMEDIATELY AFTER A COLD START: Immediately after a cold start the engine may run roughly during the catalyst heating period. Depending on the severity of this situation the malfunction indicator lamp (MIL) can be illuminated and the following fault code may be set: Fault code Control module Fault code text 151001 DME Ignition angle adjustment while idle speed cold start: ignition angle early In some circumstances if the vehicle is switched into a drive gear (R or D) when the RPM are low the engine may switch off. Should this occur the engine may be restarted normally. Software error in the DME.
Associated Products (8)Associated Documents - April 1, 2020•Document ID: 10174320Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B840214
- Date Added:
- April 27, 2020
- Manufacturer:
- BMW
SummaryCONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (271)Associated Documents - April 1, 2020•Document ID: 10174032Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- B652214
- Date Added:
- April 20, 2020
- Manufacturer:
- BMW
SummaryAUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
Associated Products (293)Associated Documents - April 1, 2020•Document ID: 10174023Service Bulletin/Repair InstructionsELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); STEERING; SUSPENSION; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B610920
- Date Added:
- April 20, 2020
- Manufacturer:
- BMW
SummaryCHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear.
Associated Products (30)Associated Documents - April 1, 2020•Document ID: 10174019Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B610520
- Date Added:
- April 20, 2020
- Manufacturer:
- BMW
SummaryCCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
Associated Products (137)Associated Documents - April 1, 2020•Document ID: 10174015Service Bulletin/Repair InstructionsPARKING BRAKE; AIR BAGS
- Mfr Comm. #:
- B513016
- Date Added:
- April 20, 2020
- Manufacturer:
- BMW
SummaryTAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
Associated Products (259)Associated Documents - February 1, 2020•Document ID: 10172500Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
- Mfr Comm. #:
- B640416
- Date Added:
- March 16, 2020
- Manufacturer:
- BMW
SummaryWater Ingress In Footwell Area From A/C Condensate Drain: This Service Information Bulletin (Revision 1) replaces SI B64 04 16 dated March 2016. The condensate drain hose is blocked by the heat shield The condensate drain hose is not attached properly to the housing The condensate drain hose was damaged during installation
Associated Products (10)Associated Documents - February 1, 2020•Document ID: 10172497Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B610520
- Date Added:
- March 16, 2020
- Manufacturer:
- BMW
SummaryCCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER. A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
Associated Products (138)Associated Documents - February 1, 2020•Document ID: 10172494Service Bulletin/Repair InstructionsVISIBILITY
- Mfr Comm. #:
- B511318
- Date Added:
- March 16, 2020
- Manufacturer:
- BMW
SummaryLIN BUS FAULTS WITH EXTERIOR REARVIEW MIRROR GLASS DAMAGE: This Service Information Bulletin (Revision 2) replaces SI B51 13 18 dated February 2020. The exterior rearview mirror glass is discolored or cracked. The power windows and folding mirrors may not operate.
Associated Products (8)Associated Documents - February 1, 2020•Document ID: 10172489Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B120420
- Date Added:
- March 16, 2020
- Manufacturer:
- BMW
SummaryMIL LIGHT ILLUMINATED AT LOW AMBIENT TEMPERATURES. After engine start the malfunction indicator lamp (MIL) and Check Control message (ID 29) "Engine fault! Power loss" are displayed in the instrument cluster. In addition The following fault codes are stored in the Digital Motor Electronics (DME) Engine runs in failsafe mode Engine cannot exceed 800 - 1200 RPMs.
Associated Products (10)Associated Documents - January 1, 2020•Document ID: 10171492Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- B520120
- Date Added:
- February 18, 2020
- Manufacturer:
- BMW
SummaryGROANING NOISE FROM TRIM APERTURE ON THE FRONT SEAT: When getting in or out of the vehicle a groaning noise can be heard from the opening (aperture) in the seat backrest. The noise may be heard from one or both of the front seats. The trim aperture in the front seat is insufficiently lubricated. The front and rear halves of the trim can contact each other causing friction noise.
Associated Products (7)Associated Documents - January 1, 2020•Document ID: 10171479Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B111219
- Date Added:
- February 18, 2020
- Manufacturer:
- BMW
SummaryMALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.
Associated Products (75)Associated Documents - January 1, 2020•Document ID: 10171414Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- B011319
- Date Added:
- February 18, 2020
- Manufacturer:
- BMW
SummarySIDE PANEL REAR LIGHT HOUSINGS: LTD WTY EXT TO 10 YEARS WITHOUT MILEAGE LIMIT: The rear light housing(s) can loosen/detach at the mounting tabs this can cause a clacking sound in the rear of the vehicle while driving. The plastic mounting tabs for the rear tail light assembly housing(s) may become too brittle and crack to the point where the hold down nut(s) can no longer keep the housing(s) in place.
Associated Products (95)Associated Documents - December 1, 2019•Document ID: 10170580Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- B522219
- Date Added:
- January 21, 2020
- Manufacturer:
- BMW
SummaryNOISE DURING FORWARD / BACK SEAT ADJUSTMENT OVER THE ENTIRE LENGTH OF TRAVEL: A loud screeching noise can be heard from the front driver's or passenger's seat during forward/back seat adjustment.
Associated Products (10)Associated Documents - November 1, 2019•Document ID: 10169468Service Bulletin/Repair InstructionsEQUIPMENT; VISIBILITY:WINDSHIELD WIPER/WASHER
- Mfr Comm. #:
- B612315
- Date Added:
- December 16, 2019
- Manufacturer:
- BMW
SummaryLow Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full : The low washer fluid warning is illuminated even though the washer fluid reservoir is full. There are no faults stored in the system for the washer fluid level switch. A non-approved washer fluid was used that is silicone-based. Silicone-based fluids are not compatible with the contactless capacitive level sensor. Fluids that contain a silicone additive are normally colored other than blue.
Associated Products (105)Associated Documents - October 1, 2019•Document ID: 10168015Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; STEERING
- Mfr Comm. #:
- B663219
- Date Added:
- November 18, 2019
- Manufacturer:
- BMW
SummaryLDW (LANE DEPARTURE WARNING): STEERING WHEEL VIBRATION NOT WORKING. LDW steering wheel vibration is not working. Software in the Body Domain Controller (BDC) control unit.
Associated Products (4)Associated Documents - October 1, 2019•Document ID: 10168008Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B611819
- Date Added:
- November 18, 2019
- Manufacturer:
- BMW
SummaryVEHICLE WILL NOT UNLOCK USING THE REMOTE CONTROL KEY BUTTON. The vehicle cannot be unlocked using the remote control key button. However, comfort access operates normally at the front door handles and the tailgate.
Associated Products (11)Associated Documents - September 1, 2019•Document ID: 10166390Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- B651419
- Date Added:
- October 21, 2019
- Manufacturer:
- BMW
SummaryHEAD UNIT NBT EVO (HU-H2) PROGRAMMING ABORT: The CID screen may light up blue. When this occurs A battery reset is not successful in restoring head unit operation Software error in the Bootloader file (BTLD) of the head unit.
Associated Products (92)Associated Documents