BMW ActiveHybrid 5 Service Bulletins (2012)
250 manufacturer communications on file.
- May 1, 2013•Document ID: 10149611Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 640513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHV Battery Expansion Valve Sticking. The high-voltage battery is cooled by refrigerant as part of the vehicle's AC system. It is regulated using an expansion valve at the base of the battery itself. This expansion valve can become stuck in the open position, either intermittently or permanently. Fault code 21F107 - Cooling valve: valve couldn't be closed will be stored in the SME. CAUSE 1. Excess material from the manufacturing process can become lodged in the valve, causing it to stick open. 2. The diagnostic software in the SME control unit is not robust enough and can lead to a fault being set when a particular threshold is reached, despite the fact that the valve is not actually sticking.
Associated Products (7)Associated Documents - May 1, 2013•Document ID: 10149610Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640413
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryRattling/Grinding Noises from Center Console. When the heating and air conditioning system is first turned on, a grinding noise may be heard from the right side of the front center console. CAUSE The bushing of the blending flap for the rear seat outlet lacks sufficient grease.
Associated Products (49)2014 BMW 528i2014 BMW 535d2014 BMW 535i2014 BMW 550i2014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72014 BMW M52013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW ActiveHybrid 7+ 29 moreAssociated Documents - May 1, 2013•Document ID: 10149608Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 613812
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (61)Associated Documents - May 1, 2013•Document ID: 10149599Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES
- Mfr Comm. #:
- 510913
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"The Door Springs into Pre-Locking Position. When the customer closes the door, it may seem that the door has closed completely. However, it is only in the pre-locking position, not the fully locked position. A check control message indicates that the door is open. 3.Close the front door and pull the outer door handle to the ""trigger point"" when the door first pops open. Measure the distance from the edge of the inside of the outer door handle to the metal door skin, as shown. The ""trigger"" distance should be between 24 mm-27 mm. Note: A scale or tape measure is physically too large to accurately make this measurement. A sliding caliper must be used for accuracy. Note: The door will not completely open when either in the pre-locking or the fully locked position CAUSE * Door adjustment (closing effort too high) * Incorrect routing of the Bowden cable (outside and inside door handle). Heavy accumulation of dirt and grime in the door lock."
Associated Products (17)Associated Documents - May 1, 2013•Document ID: 10149596Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340213
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model
Associated Products (59)Associated Documents - May 1, 2013•Document ID: 10149592Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- 240313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN52T/N55 with 8HP45: Delay in Engine Response. When slowing down to lower suburban road speeds and then accelerating, a delay in engine response may be experienced. This situation may be more noticeable when driving in a bend in the road or on roads with a rising gradient. Unfavorable EGS and DME software calibration
Associated Products (18)Associated Documents - May 1, 2013•Document ID: 10149590Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (69)Associated Documents - May 1, 2013•Document ID: 10149582Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 120713
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryElectric Vacuum Pump Intermittent Failure. The check engine light (CEL) is illuminated and the MSA malfunction check control message is present. No electric driving is possible. This situation may be intermittent or permanent. The following fault codes are stored in the Electric Machine Electronics (EME): * 2202ED - Brake-servo assistance: Mechanical ventilation flap control blocked, time threshold 2 exceeded * 2202EC - Brake-servo assistance: Mechanical ventilation flap control blocked, time threshold 1 exceeded CAUSE Internal mechanical failure of the electric vacuum pump. If intermittent, this leads to reduced vacuum and thus the associated fault codes. If not repaired, the amount of damage to the pump will increase to the point of a permanent failure.
Associated Products (6)Associated Documents - April 1, 2013•Document ID: 10149494Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 840113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMTelephone: Phonebook Does Not Transfer to the Vehicle. The telephone book does not transfer to the vehicle after the pairing process is completed. CAUSE Software error in the head unit
Associated Products (15)Associated Documents - April 1, 2013•Document ID: 10149491Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Hardware error in the Headunit-High"
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149489Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 650613
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryCHAMP2: Integrated Cooling Fan Is Noisy Intermittently. Intermittently, the cooling fan integrated in the CHAMP2 head unit (Radio Professional) is noisy. * More noticeable after the ignition is turned off * The cooling fan runs for approx. 6 minutes (until CHAMP2 enters sleep mode), depending on the ambient temperature Settings of the fan characteristics: the fan keeps running after the ignition is turned off
Associated Products (17)Associated Documents - April 1, 2013•Document ID: 10149488Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 640113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMRed or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149340Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 121612
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary?SI B12 16 12 Engine Electrical Systems April 2013 Technical Service This Service Information bulletin supersedes SI B12 16 12 dated September 2012. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Program Control Units (OBD Communication). The vehicles affected by this Service Action require a vehicle software update in order to address non-compliance pertaining to an incomplete parameter in the OBD (onboard diagnostics) test process.
Associated Products (3)Associated Documents - April 1, 2013•Document ID: 10149338Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 120912
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIntermittently, the engine idle speed may fluctuate up and down or cut off under any of the following circumstances, without any relevant faults stored in the DME memory: * While driving off throttle (coasting) and braking at speeds below approx. 10 mph * While idling, low-speed maneuvering such as parking, or if the steering is turned to the full-lock position Unfavorable DME software
Associated Products (23)Associated Documents - April 1, 2013•Document ID: 10149336Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 120113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Transmission Intermittently Goes into ""P"" or ""N"" after MSA Engine Start. The transmission can intermittently go into the Park (P) or Neutral (N) position after an MSA engine start without any customer influence. This problem is very sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software"
Associated Products (16)Associated Documents - April 1, 2013•Document ID: 10149335Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
Associated Products (69)Associated Documents - March 1, 2013•Document ID: 10150135Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840413
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"TCB: Emergency Call Is Disabled. A Check Control message shows ""Emergency call failure."" When the SOS button is pressed, the call is not made by the TCB (Telematics Communication Box). Fault code 0XB7F33F is stored in the TCB. CAUSE TCB application error"
Associated Products (42)Associated Documents - March 1, 2013•Document ID: 10150132Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 651113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryCIS Seat Mat Replacement. Installation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
Associated Products (55)Associated Documents - March 1, 2013•Document ID: 10150130Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 651009
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (173)Associated Documents - March 1, 2013•Document ID: 10150129Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- 650913
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"CHAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite) are no longer available in: * Menu ""PRESETS"" * Functional bookmarks (buttons on the head unit) Error in the CHAMP2 head unit"
Associated Products (17)Associated Documents