BMW 760Li Service Bulletins (2010)
244 manufacturer communications on file.
- October 1, 2013•Document ID: 10150266Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 651113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryInstallation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
Associated Products (57)Associated Documents - October 1, 2013•Document ID: 10150263Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 640113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"IHKA Operating Panel Buttons Are Peeling. INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the ""Repair kit for button caps"" when performing this repair. Replace ALL the buttons with those included in the kit. Note: Please do not use and claim the part number for the "Repair kit, radio and A/C panel." To ensure the button cap kit with the correct symbols and labels is installed, perform a part number lookup in ETK by VIN. Labor operation code 64 11 326 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 64 11 769 instead."
Associated Products (57)Associated Documents - October 1, 2013•Document ID: 10150257Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (71)Associated Documents - October 1, 2013•Document ID: 10150256Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130413
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.
Associated Products (77)Associated Documents - September 1, 2013•Document ID: 10152356Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840713
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"""Message"" Option Is Missing After Programming. Messages can be sent to the vehicle and are received as indicated by the envelope icon displayed in the CID. However, the menu option ""Message,"" used to retrieve or access messages, is no longer available in the iDrive menu. CAUSE Software error with ISTA/P 2.49.2 to 2.49.4 I-Level F001-13-03-503 to F001-13-03-505"
Associated Products (49)2014 BMW 528i2014 BMW 535d2014 BMW 535i2014 BMW 550i2014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72014 BMW M52013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW ActiveHybrid 7+ 29 moreAssociated Documents - September 1, 2013•Document ID: 10152347Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130413
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013
Associated Products (77)Associated Documents - August 1, 2013•Document ID: 10150235Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 651913
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryHU-H: SDARS Radio Stations Cannot Be Stored in PRESET Menu. The SIRIUS/XM satellite radio (SDARS) stations cannot be stored in the PRESET menu. * No fault code related to this issue is stored in the HU-H. * AM/FM radio stations are not affected; they can be stored correctly. Software error in the SDARS control unit integrated in the Headunit-High (HU-H)
Associated Products (59)Associated Documents - August 1, 2013•Document ID: 10150232Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 641510
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryFault Code for Ionizer Short to Ground Is Stored in the IHKA. INFORMATION Not applicable.
Associated Products (25)2012 BMW 528i2012 BMW 535i2012 BMW 550i2012 BMW 740i2012 BMW 740Li2012 BMW 750i2012 BMW 750Li2012 BMW 760Li2012 BMW ActiveHybrid 52012 BMW ActiveHybrid 72011 BMW 528i2011 BMW 535i2011 BMW 550i2011 BMW 740i2011 BMW 740Li2011 BMW 750i2011 BMW 750Li2011 BMW 760Li2011 BMW ActiveHybrid 72011 BMW R 1200 GS+ 5 moreAssociated Documents - August 1, 2013•Document ID: 10150231Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 630513
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"FRM3 Will Not Communicate with ISTA. When diagnosing the vehicle with ISTA, the FRM3 (Footwell Module) is shown as not responding in the vehicle test. The customer may report one or more of the following malfunctions: 1. Light operation * CCM (Check Control Message) ""Display failure"" * Lighting INOP * Turn signal lights INOP * Break lights INOP * License plate light INOP * Courtesy lights INOP * Instrument cluster w/o light 2. Windows * One or both front windows INOP 3. LIN components https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15625.1.B630513... 8/29/2013 Page 2 of 2 * CCM ""no blind spot detection"" if equipped * Power mirrors INOP * Seat adjustment INOP 4. Hardware inputs * Door locks INOP * Gear shifts automatically to P * Gear shift lever cannot be moved out of P 5. Electrical steering column adjustment * ELSV (Electric Steering Column Adjustment) INOP CAUSE Various causes include the following: * Blown fuse * Faulty wiring * Faulty component"
Associated Products (61)Associated Documents - August 1, 2013•Document ID: 10150219Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310112
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (71)Associated Documents - July 1, 2013•Document ID: 10150038Service Bulletin/Repair InstructionsSTRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- 511409
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryAutomatic Trunk Lid Does Not Close Properly. Intermittently, the automatic trunk lid (HKL) will not close properly. When the automatic close button on the trunk lid is pressed, the trunk lid will begin closing and then reopen, just before it reaches the end of travel. Closing the trunk manually will allow it to properly latch closed. No relevant fault codes are stored. CAUSE Software error in the HKL control unit
Associated Products (5)Associated Documents - June 1, 2013•Document ID: 10150076Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- 620613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (70)Associated Documents - June 1, 2013•Document ID: 10150070Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummarySqueaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
Associated Products (40)Associated Documents - June 1, 2013•Document ID: 10150069Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 270213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryKnocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
Associated Products (40)Associated Documents - May 1, 2013•Document ID: 10149618Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 840613
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION Part Number
Associated Products (72)Associated Documents - May 1, 2013•Document ID: 10149610Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640413
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryRattling/Grinding Noises from Center Console. When the heating and air conditioning system is first turned on, a grinding noise may be heard from the right side of the front center console. CAUSE The bushing of the blending flap for the rear seat outlet lacks sufficient grease.
Associated Products (49)2014 BMW 528i2014 BMW 535d2014 BMW 535i2014 BMW 550i2014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72014 BMW M52013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW ActiveHybrid 7+ 29 moreAssociated Documents - May 1, 2013•Document ID: 10149608Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 613812
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (61)Associated Documents - May 1, 2013•Document ID: 10149596Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340213
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model
Associated Products (59)Associated Documents - May 1, 2013•Document ID: 10149590Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (69)Associated Documents - May 1, 2013•Document ID: 10149589Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- 130409
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
Associated Products (120)Associated Documents