BMW 535i Service Bulletins (2013)
399 manufacturer communications on file.
- June 1, 2013•Document ID: 10150076Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- 620613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (70)Associated Documents - June 1, 2013•Document ID: 10150070Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummarySqueaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
Associated Products (40)Associated Documents - June 1, 2013•Document ID: 10150069Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 270213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryKnocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
Associated Products (40)Associated Documents - June 1, 2013•Document ID: 10150068Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- 121712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryA customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
Associated Products (22)Associated Documents - June 1, 2013•Document ID: 10150066Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121313
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine Does Not Start on First Attempt when Cold. The engine turns over but does not start on the first attempt. It will normally start on the second or third attempt, and no faults are stored in the DME. This occurs sporadically, usually at low ambient temperatures and when the engine is also cold. Unfavorable DME software in conjunction with a partially charged battery
Associated Products (5)Associated Documents - May 1, 2013•Document ID: 10149618Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 840613
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION Part Number
Associated Products (72)Associated Documents - May 1, 2013•Document ID: 10149617Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryTCB: Emergency Call Is Erroneously Triggered. An emergency call is erroneously made with no input from the driver. The following fault codes are stored in the TCB: * 0xB7F325 - Emergency call loud speaker: break in circuit * 0xB7F319 - Emergency call button: short circuit * 0xB7F326 - Emergency call loud speaker: short circuit to earth * 0xB7F33E - Automatic emergency call triggered frequently CAUSE TCB control unit error
Associated Products (51)Associated Documents - May 1, 2013•Document ID: 10149614Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 660313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryParking Assistant Inoperative After Programming. The parking assistant system does not function correctly. One or more of the following scenarios may occur: * Unable to activate the parking assistant via the iDrive * When activated, the vehicle does not locate a parking spot * Does not assist with parking the vehicle CAUSE Software error in ISTA/P 2.49.0 programming data
Associated Products (25)Associated Documents - May 1, 2013•Document ID: 10149610Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640413
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryRattling/Grinding Noises from Center Console. When the heating and air conditioning system is first turned on, a grinding noise may be heard from the right side of the front center console. CAUSE The bushing of the blending flap for the rear seat outlet lacks sufficient grease.
Associated Products (49)2014 BMW 528i2014 BMW 535d2014 BMW 535i2014 BMW 550i2014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72014 BMW M52013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW ActiveHybrid 7+ 29 moreAssociated Documents - May 1, 2013•Document ID: 10149608Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 613812
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (61)Associated Documents - May 1, 2013•Document ID: 10149599Service Bulletin/Repair InstructionsLATCHES/LOCKS/LINKAGES
- Mfr Comm. #:
- 510913
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"The Door Springs into Pre-Locking Position. When the customer closes the door, it may seem that the door has closed completely. However, it is only in the pre-locking position, not the fully locked position. A check control message indicates that the door is open. 3.Close the front door and pull the outer door handle to the ""trigger point"" when the door first pops open. Measure the distance from the edge of the inside of the outer door handle to the metal door skin, as shown. The ""trigger"" distance should be between 24 mm-27 mm. Note: A scale or tape measure is physically too large to accurately make this measurement. A sliding caliper must be used for accuracy. Note: The door will not completely open when either in the pre-locking or the fully locked position CAUSE * Door adjustment (closing effort too high) * Incorrect routing of the Bowden cable (outside and inside door handle). Heavy accumulation of dirt and grime in the door lock."
Associated Products (17)Associated Documents - May 1, 2013•Document ID: 10149597Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 340612
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV
Associated Products (44)Associated Documents - May 1, 2013•Document ID: 10149596Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340213
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model
Associated Products (59)Associated Documents - May 1, 2013•Document ID: 10149593Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 270212
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV"
Associated Products (39)Associated Documents - May 1, 2013•Document ID: 10149592Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- 240313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN52T/N55 with 8HP45: Delay in Engine Response. When slowing down to lower suburban road speeds and then accelerating, a delay in engine response may be experienced. This situation may be more noticeable when driving in a bend in the road or on roads with a rising gradient. Unfavorable EGS and DME software calibration
Associated Products (18)Associated Documents - May 1, 2013•Document ID: 10149590Service Bulletin/Repair InstructionsENGINE; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (69)Associated Documents - May 1, 2013•Document ID: 10149581Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 120513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryService Engine Soon Light Flashes with Throttle Adaptation Faults Stored. The EML light flashes with a check control message for reduced power output and/or the Service Engine Soon lamp (MIL) flashes. During the throttle valve adaptation (teach-in limit run), faults may occur due to signal voltage oscillations. This could lead to a termination of the teach-in routine or an incorrect value taught in at the lower limit. The following faults can be stored in the DME memory: E82, E84, E88, E89, E92, and E93 BN2000 vehicles * 28D0: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 28D4: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 28C4: throttle valve, adaptation: Emergency air position not adapted * 28A0: throttle valve angle - Intake manifold absolute comparison: pressure too high ??3166: Tank-ventilation system: fault F01, F02, F06, F07, F10, F12, F13, F30, F31, and ALPINA B7 BN2020 vehicles: * 101408: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 107AE0: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 101402: throttle valve, adaptation: Emergency air position not adapted * 101F01: throttle valve angle - Intake manifold absolute comparison: pressure too high ??190F08: Tank-ventilation system: fault Sensitivity of the throttle valve sensor (only affects parts installed during this production period)
Associated Products (38)Associated Documents - April 1, 2013•Document ID: 10149494Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 840113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMTelephone: Phonebook Does Not Transfer to the Vehicle. The telephone book does not transfer to the vehicle after the pairing process is completed. CAUSE Software error in the head unit
Associated Products (15)Associated Documents - April 1, 2013•Document ID: 10149491Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Hardware error in the Headunit-High"
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149489Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 650613
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryCHAMP2: Integrated Cooling Fan Is Noisy Intermittently. Intermittently, the cooling fan integrated in the CHAMP2 head unit (Radio Professional) is noisy. * More noticeable after the ignition is turned off * The cooling fan runs for approx. 6 minutes (until CHAMP2 enters sleep mode), depending on the ambient temperature Settings of the fan characteristics: the fan keeps running after the ignition is turned off
Associated Products (17)Associated Documents