BMW 335i Service Bulletins (2015)
436 manufacturer communications on file.
- February 1, 2014•Document ID: 10147982Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 652313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
Associated Products (98)Associated Documents - February 1, 2014•Document ID: 10147981Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 650414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Airbag Warning Light: ACSM FC 930A60 Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
Associated Products (88)Associated Documents - February 1, 2014•Document ID: 10147980Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147979Service Bulletin/Repair InstructionsVISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 640114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Heating and Air Conditioner. There is an intermittent whirring noise from the IHKA system when the engine is under load between 2,000 and 3,000 rpm, and sometimes at approximately 5,000 rpm. CAUSE Vibrations from the A/C low-pressure hose are resonating into the heating and air conditioning system.
Associated Products (11)Associated Documents - February 1, 2014•Document ID: 10147976Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThe Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (88)Associated Documents - February 1, 2014•Document ID: 10147973Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY
- Mfr Comm. #:
- 510714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147972Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog.
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents - January 1, 2014•Document ID: 10147952Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.
Associated Products (90)Associated Documents - January 1, 2014•Document ID: 10147950Service Bulletin/Repair InstructionsVISIBILITY; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents - January 1, 2014•Document ID: 10147936Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove Water Drain Plugs from E-Box. The water drain plugs for the left- and right-side E-box may clog. This can lead to water collection/corrosion and allow water to enter the passenger compartment. CAUSE The water drain plug slots are too small.
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147933Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- 340913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBrake Squeal. Squeaking noises from the front or rear axle when braking. The squeaking noise when braking may have different causes, depending on the axle.
Associated Products (4)Associated Documents - January 1, 2014•Document ID: 10147929Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE
- Mfr Comm. #:
- 180213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Exhaust Flap Actuator Is Loose. INFORMATION Covered under the terms of the BMW New Vehicle/SAV Limited Warranty Defect Code:18 12 03 39 00https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Labor Operation:Labor Allowance:Refer to KSDReplacing exhaust flap actuator driveLabor operation code 18 12 081 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 18 12 581 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field."
Associated Products (16)Associated Documents - January 1, 2014•Document ID: 10147706Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
Associated Products (54)Associated Documents