Audi A8 Service Bulletins (2013)
1,506 manufacturer communications on file.
- September 11, 2013•Document ID: 10210655Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 37 13 17 2029027
- Date Added:
- May 2, 2022
- Manufacturer:
- AUDI
SummaryThe DTCs are stored due to an issue with the transmission control module software. Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). ? DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. ? DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.
Associated Products (14)Associated Documents - September 11, 2013•Document ID: 10068748Service Bulletin/Repair InstructionsLANE DEPARTURE: ASSIST
- Mfr Comm. #:
- 2034000/2
- Date Added:
- June 2, 2016
- Manufacturer:
- AUDI
SummarySUMMARY TO BE PROVIDED ON A FUTURE DATE.
Associated Products (7)Associated Documents - September 11, 2013•Document ID: 10121373Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- A961374 2034000-
- Date Added:
- October 31, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 96 number 13-63 dated May 29, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative. Message ?Side Assist Unavailable? is displayed in the Driver Information Display when the system deactivates. Audi Lane Change Assistant can be activated without issue. DTCs are stored in the Lane Change Assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi Lane Change Assistant temporarily.
Associated Products (9)Associated Documents - September 11, 2013•Document ID: 10121367Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- A911304 2013422-
- Date Added:
- October 31, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
Associated Products (117)Associated Documents - September 11, 2013•Document ID: 10121362Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:WIRING
- Mfr Comm. #:
- A801305 2033806-
- Date Added:
- October 31, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
Associated Products (24)Associated Documents - September 11, 2013•Document ID: 10121329Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- A371317 2029027-
- Date Added:
- October 31, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 37 number 13-02 dated April 26, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs is stored in the transmission control module (TCM). If DFCCs do not match exactly, this TSB does not apply.
Associated Products (17)Associated Documents - September 11, 2013•Document ID: 10054865Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- TSB-37-13-17
- Date Added:
- March 6, 2014
- Manufacturer:
- AUDI
SummaryAUDI: THE TRANSMISSION CONTROL MODULE SOFTWARE WOULD ILLUMINATE IN INSTRUMENT CLUSTER AND VEHICLE FAILS TO MOVE AFTER SHIFTING INTO GEAR AND NEW SOFTWARE IS NEEDED TO ADDRESS CONDITION. *PE
Associated Products (15)Associated Documents - September 10, 2013•Document ID: 10121363Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS
- Mfr Comm. #:
- A871345 2024644-
- Date Added:
- October 31, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 87 number 13-41 dated May 30, 2013. Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.
Associated Products (26)Associated Documents - September 5, 2013•Document ID: 10121324Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- A101310 2018288-
- Date Added:
- October 31, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
Associated Products (154)Associated Documents - August 30, 2013•Document ID: 10124638Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- A911302 2018187-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
Associated Products (125)Associated Documents - August 26, 2013•Document ID: 10124655Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- A461358 2035113-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryCustomer may report rattling noises from front axle on uneven roads. There are conflicting tolerances in the alignment of pin and hole on the front brake discs.
Associated Products (3)Associated Documents - August 26, 2013•Document ID: 10124641Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- A871344 2020124-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 87 number 13-43 dated July 12, 2013. Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.
Associated Products (39)Associated Documents - August 26, 2013•Document ID: 10124592Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- Update Bulletin
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryOn Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24Z6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on.
Associated Products (14)Associated Documents - August 23, 2013•Document ID: 10124644Service Bulletin/Repair InstructionsSTRUCTURE:BODY:DOOR; VISIBILITY:POWER WINDOW DEVICES AND CONTROLS
- Mfr Comm. #:
- A641330 2034955-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 64 number 13-28 dated August 12, 2013. There are squeaking noises coming from the front door when the window is operated. When the window guide seal is not correctly fitted in the rail of the front door, it can lead to increased friction. This increased resistance causes the squeaking noises.
Associated Products (2)Associated Documents - August 16, 2013•Document ID: 10124671Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER
- Mfr Comm. #:
- A211317 2034999-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryOn 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger. The crankcase breather is only connected to the bank 2 turbocharger inlet. Blow-by gases from the crankcase breather discolor the pipe. This is a normal condition.
Associated Products (18)Associated Documents - August 16, 2013•Document ID: 10124656Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- A461357 2031135-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummarySupersedes Technical Service Bulletin Group 46 number 12-26 dated October 23, 2012. The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module. There is an issue with the software in the EPB control module that occurs one time. Because the issue only occurs once, replacing the control module could cause an additional occurrence.
Associated Products (12)Associated Documents - August 14, 2013•Document ID: 10124645Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD
- Mfr Comm. #:
- A641329 2020552-
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryWindshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Associated Products (144)Associated Documents - August 14, 2013•Document ID: 10124621Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
- Mfr Comm. #:
- AWA-13-07
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryAs part of Audi's ongoing commitment to our environment, Audi is extending the Emissions Control Systems Warranty to cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 years or 120,000 miles, whichever occurs first, from the vehicle's original in-service date for certain 2009-12 Model Year Audi vehicles with 3.2L engine, and certain 2009-2013 Model Year Audi vehicles with 3.0T engines. The vehicle's original in-service date is defined as the date the vehicle was delivered to either the original purchaser or the original lessee; or if the vehicle was first placed in service as a "demonstrator" or "company" car, on the date such vehicle was first placed in service. The warranty extension is fully transferable to subsequent owners. Audi has determined that under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary airports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of the on-board diagnostic system. In some locales, an illuminated MIL could cause the vehicle to fail an IM emissions inspection, vehicle registration application could be denied. Audi will diagnose, and if necessary clean the engine cylinder head secondary air ports to remove the carbon buildup at no cost to the customer as long as the vehicle is within the time and mileage limits of the warranty extension. This warranty extension covers only the diagnosis and cleaning of the cylinder head secondary air ports to remove the carbon buildup. Reimbursement is applicable only to the repairs described in this Warranty Bulletin.
Associated Products (42)Associated Documents - August 14, 2013•Document ID: 10124609Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- Dealer Letter-Up
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryThis communication is to inform you of a revision to Update 24Z6. The revision is in regards to the manifold actuator.
Associated Products (14)Associated Documents - August 13, 2013•Document ID: 10124616Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- Customer Letter
- Date Added:
- December 5, 2017
- Manufacturer:
- AUDI
SummaryAudi has determined that, under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary air ports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions.
Associated Products (42)Associated Documents