Mercedes-Benz C-Class Service Bulletins (2021)

229 manufacturer communications on file.

• January 9, 2025•Document ID: 11012807

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI20.10-P-076206

  Date Added:

  January 10, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Customer states that the CEL is lit in the instrument cluster Cause Debris in the coolant system Remedy Please refer to the specific repair instructions for the vehicle you are working on in the attachments section of this LI. Before beginning work on the vehicle open a TIPS case and request the tool you will need. In your request include a contact name, phone number, and shipping address for the tool to be sent. Before the tool arrives: • Remove and replace the coolant expansion tank (reservoir) and the main radiator. • Without removing the components: flush the heater core and changeover valve (located in the right front wheel arch) in the opposite direction of flow until no debris remains. Once the tool arrives, proceed with flushing the vehicle per the instructions attached in this LI. A picture of the filter after each flush must be taken. If after the prescribed number of flushing attempts debris is still being collected in the filter, upload all the pictures to the TIPS case and wait for next steps. A scale of not-acceptable to acceptable debris level in the filter is in the attachments for you to make an assessment as well.

  Associated Products (13)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz CLA-Class
  Associated Documents

  • DownloadMC-11012807-0001.pdf↗
• November 27, 2024•Document ID: 11010970

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 24P5497813

  Date Added:

  December 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

  Associated Products (46)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class+ 26 more
  Associated Documents

  • DownloadMC-11010970-0001.pdf↗
• November 25, 2024•Document ID: 11010907

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-066284

  Date Added:

  December 2, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360° system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10° (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10°. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.

  Associated Products (89)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class+ 69 more
  Associated Documents

  • DownloadMC-11010907-0001.pdf↗
• November 20, 2024•Document ID: 11010818

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.19-P-072588

  Date Added:

  November 27, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.

  Associated Products (189)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class+ 169 more
  Associated Documents

  • DownloadMC-11010818-0001.pdf↗
• November 20, 2024•Document ID: 11010755

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-078473

  Date Added:

  November 23, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": • The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": • The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

  Associated Products (147)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class+ 127 more
  Associated Documents

  • DownloadMC-11010755-0001.pdf↗
• November 13, 2024•Document ID: 11010494

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING; VISIBILITY/WIPER

  Mfr Comm. #:

  LI82.10-P-078069

  Date Added:

  November 13, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely – some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (40–50 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.

  Associated Products (112)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class+ 92 more
  Associated Documents

  • DownloadMC-11010494-0001.pdf↗
• November 12, 2024•Document ID: 11010455

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.10-P-075869

  Date Added:

  November 12, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data

  Associated Products (89)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class+ 69 more
  Associated Documents

  • DownloadMC-11010455-0001.pdf↗
• October 23, 2024•Document ID: 11009122

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY; VISIBILITY/WIPER

  Mfr Comm. #:

  LI82.35-P-078467

  Date Added:

  October 25, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

  Associated Products (265)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 245 more
  Associated Documents

  • DownloadMC-11009122-0001.pdf↗
• October 4, 2024•Document ID: 11008712

  Service Bulletin/Repair Instructions
  ENGINE; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI01.20-P-078446

  Date Added:

  October 8, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. • The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.

  Associated Products (69)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz A-Class+ 49 more
  Associated Documents

  • DownloadMC-11008712-0001.pdf↗
• October 3, 2024•Document ID: 11008880

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-078473

  Date Added:

  October 9, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": • The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": • The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). • In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.

  Associated Products (134)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLE-Class+ 114 more
  Associated Documents

  • DownloadMC-11008880-0001.pdf↗
• October 1, 2024•Document ID: 11008873

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.00-P-074450

  Date Added:

  October 9, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).

  Associated Products (44)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz S-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz S-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz S-Class2019 Mercedes-Benz C-Class2019 Mercedes-Benz E-Class2019 Mercedes-Benz S-Class2018 Mercedes-Benz C-Class2018 Mercedes-Benz E-Class2018 Mercedes-Benz S-Class+ 24 more
  Associated Documents

  • DownloadMC-11008873-0001.pdf↗
• September 28, 2024•Document ID: 11008091

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.70-P-077433

  Date Added:

  September 28, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11008091-0001.pdf↗
• September 21, 2024•Document ID: 11007974

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078307

  Date Added:

  September 24, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11007974-0001.pdf↗
• September 17, 2024•Document ID: 11008032

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-063502

  Date Added:

  September 25, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: • Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it • Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) • Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: • Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) • Select a suitable route • Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications • Finally drive approx. 5 km to allow the system to cool • Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: • Observe SI00.00-P-0086A • Have parts already been replaced? If yes, when and which parts (date, mileage)? • How is the customer's driving profile, and when/where is it reproducible? • Create a video/ sound file • Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)

  Associated Products (128)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLC-Class+ 108 more
  Associated Documents

  • DownloadMC-11008032-0001.pdf↗
• September 16, 2024•Document ID: 11008056

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI07.70-P-078078

  Date Added:

  September 26, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.

  Associated Products (40)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz A-Class+ 20 more
  Associated Documents

  • DownloadMC-11008056-0001.pdf↗
• September 10, 2024•Document ID: 11008323

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078302

  Date Added:

  October 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.

  Associated Products (119)

  2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class+ 99 more
  Associated Documents

  • DownloadMC-11008323-0001.pdf↗
• September 10, 2024•Document ID: 11007753

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  September 13, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11007753-0001.pdf↗
• September 9, 2024•Document ID: 11007790

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078304

  Date Added:

  September 14, 2024

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.

  Associated Products (109)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz S-Class+ 89 more
  Associated Documents

  • DownloadMC-11007790-0001.pdf↗
• September 9, 2024•Document ID: 11007728

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.00-P-075630

  Date Added:

  September 12, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LI’s before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?

  Associated Products (85)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class+ 65 more
  Associated Documents

  • DownloadMC-11007728-0001.pdf↗
• August 30, 2024•Document ID: 11006710

  Over The Air
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20240830

  Date Added:

  August 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.

  Associated Products (19)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz C-Class2021 Mercedes-Benz GLC-Class2021 Mercedes-Benz S-Class
  Associated Documents

  • DownloadMC-11006710-0001.pdf↗