BMW 650i Service Bulletins (2016)
231 manufacturer communications on file.
- May 1, 2016•Document ID: 10151333Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL
- Mfr Comm. #:
- B660916
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
Associated Products (126)Associated Documents - May 1, 2016•Document ID: 10151328Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- B630416
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryLED Headlight CCM/Output Decrease. Any of the following may be evident: CCM about front headlights Headlight output decreases during operation 8059AFFan 1: Line disconnection / 8059AE Fan 1: Short circuit / Headlight fan failure
Associated Products (9)Associated Documents - May 1, 2016•Document ID: 10151324Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B620716
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryUnintentional Active ECO-PRO Bonus Miles Reset. Fluctations of fuel level (causing resistance changes in the level sensor) while vehicle is stationary, are interpreted as refueling. This causes active ECO PRO mode bonus range to reset. Error in instrument cluster application.
Associated Products (82)Associated Documents - May 1, 2016•Document ID: 10151317Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD
- Mfr Comm. #:
- B511516
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryDelivery Stop - Check/Replace Windshield Sealing.
Associated Products (17)Associated Documents - May 1, 2016•Document ID: 10151312Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- B320616
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryTroubleshooting intermittent Steering Assistance with Electric Power Steering (EPS). Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.
Associated Products (88)Associated Documents - May 1, 2016•Document ID: 10151303Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- B111715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
Associated Products (104)Associated Documents - May 1, 2016•Document ID: 10151302Service Bulletin/Repair InstructionsPOWER TRAIN; POWER TRAIN:CLUTCH ASSEMBLY:BELL HOUSING
- Mfr Comm. #:
- B110916
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryN63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
Associated Products (96)Associated Documents - April 14, 2016•Document ID: 10216791Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- TEC24
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryTech24 Snap-in Adapter Return
Associated Products (59)Associated Documents - April 1, 2016•Document ID: 10216793Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- TEC26
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryTEC26 Turbo Charger Return
Associated Products (59)Associated Documents - April 1, 2016•Document ID: 10151274Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B840715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
Associated Products (127)Associated Documents - April 1, 2016•Document ID: 10151264Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- B520116
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryFront Seat Backrests Vibrates on Rough Roads. Both front seat backrests vibrate and rattle while driving over rough roads with the seat in an unloaded condition (no pressure applied on the backrest). Play at the inner backrest pivot point.
Associated Products (24)Associated Documents - April 1, 2016•Document ID: 10151250Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B120516
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N55 - Engine Malfunction Warning Due to Vapor Forming in the Fuel System. The Engine Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."
Associated Products (48)Associated Documents - March 21, 2016•Document ID: 10216792Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- TEC25
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryTec25 Wishbone Return
Associated Products (59)Associated Documents - March 1, 2016•Document ID: 10216758Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- SIM110115
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryMINI engine oil part number transition and model year 2016 engine oils
Associated Products (59)Associated Documents - March 1, 2016•Document ID: 10216757Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SIM010603
- Date Added:
- August 1, 2022
- Manufacturer:
- BMW
SummaryMINI "Enhanced" dealer self authorized (DSA)K goodwill program
Associated Products (59)Associated Documents - March 1, 2016•Document ID: 10151206Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B840715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
Associated Products (20)Associated Documents - March 1, 2016•Document ID: 10151200Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT
- Mfr Comm. #:
- B651316
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
Associated Products (79)Associated Documents - March 1, 2016•Document ID: 10151197Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- B650716
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryNBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
Associated Products (158)Associated Documents - March 1, 2016•Document ID: 10151196Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- B650616
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryNBT Head Unit Aborts Import of CD. While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
Associated Products (159)Associated Documents - March 1, 2016•Document ID: 10151190Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B640316
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm
Associated Products (117)Associated Documents