BMW 435i Service Bulletins (2015)
391 manufacturer communications on file.
- October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149381Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660814
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummarySide View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
Associated Products (101)Associated Documents - October 1, 2014•Document ID: 10149380Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 651914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDWA Siren Malfunction. When the anti-theft alarm (DWA) is triggered, the horn comes on instead of the alarm siren. DWA internal monitoring is too sensitive.
Associated Products (15)Associated Documents - October 1, 2014•Document ID: 10149379Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
Associated Products (53)Associated Documents - October 1, 2014•Document ID: 10149377Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 631014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryAdaptive Headlight Malfunction. A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.
Associated Products (46)Associated Documents - October 1, 2014•Document ID: 10149376Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryLED Headlight Malfunction. 1. The LED headlight on one side malfunctions. 2. One headlight flickers on and off while driving (problem is sporadic). 3. The Check Control message indicates the parking light or driving light is defective. One or more of the following faults can be stored: 805980 Low-beam headlight defective 805981 High-beam headlight defective 8044BB Right-hand LED main light module (LHM2) implausible low-beam headlight function status 8044BA Left-hand LED main light module (LHM2) implausible low-beam headlight function status CAUSE The situation above is caused by a poor connection at the LED headlight connector or LED main light module.
Associated Products (11)Associated Documents - October 1, 2014•Document ID: 10149375Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 620414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Instrument Cluster. The display in the instrument cluster is inoperative.
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149371Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 612614
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHorn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: "8044A3 - Wiring, horn short circuit to earth" "8044A4 - Wiring, horn short circuit to positive" "8044A5 - Wiring, horn relay is defective or short circuit to positive" Water has entered the horn and caused it to fail internally (shorted out).
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149365Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryPower-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues. The following codes may be stored in the fault memory of the Electric Power Steering (EPS): Scenario 1: 0x4823E1 Scenario 2: 0x4823CB/0x4823CC Scenario 3: 0x4823D2 and/or 0x4823EC Scenario 4: 0x48239C (DSC warning lamp lights up in the instrument cluster) Scenario 5: No communication with the EPS is possible (not accessible using diagnostics) Scenario 6: 0x4823EE and 0x4823C2
Associated Products (24)Associated Documents - October 1, 2014•Document ID: 10149363Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryFront Suspension Ride Height Has Dropped. INFORMATION Damages due to outside influences are not covered under the terms of the BMW limited warranties.
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149355Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
Associated Products (58)Associated Documents - October 1, 2014•Document ID: 10149351Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 122914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryReduced Engine Performance. When driving with high outside ambient temperatures, repeated stop and go, or high-load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances, the compressor is switched off. One or both of the following faults are stored in the DME: 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault 241400: Electric fan, diagnosis feedback 1: Fan slightly stiff The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 600W electric fan over-boost or high speed function 2. The electric cooling fan design was not robust enough for continuous over-boost or high-speed operation.
Associated Products (18)Associated Documents - September 1, 2014•Document ID: 10148042Service Bulletin/Repair InstructionsVISIBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 660714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTop Rear Side View Camera Control Unit Rattles While Driving. While driving, a rattling-type noise is heard coming from the lower windshield area up behind the instrument panel (driver's side). CAUSE The TRSVC (Top Rear Side View Camera) control module support bracket is loose.
Associated Products (22)Associated Documents - September 1, 2014•Document ID: 10148039Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"
Associated Products (40)Associated Documents - August 1, 2014•Document ID: 10148380Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCentral Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.
Associated Products (68)Associated Documents - August 1, 2014•Document ID: 10148373Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 620214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHead-Up Display Inoperative. The Head-up Display is inoperative. Fault code 0xB7F6E3 - HUD: Communication error (HUD does not answer) is stored in the Instrument Cluster (KOMB25). A software error in the instrument cluster prevents the Head-up Display from activating.
Associated Products (20)Associated Documents - August 1, 2014•Document ID: 10148372Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT
- Mfr Comm. #:
- 612214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFC 80402E Stored After Replacement of Rear Electronics Module. After replacement of the Rear Electronics Module (REM), fault code "0x80482E - Incorrect HW variant" is stored and cannot be cleared. This fault has no effect on the vehicle functions and is not noticed by the customer. CAUSE The replacement REM is always supplied as a "High variant." The fault is stored because the F33 does not have a rear window anti-trap circuit.
Associated Products (4)Associated Documents - August 1, 2014•Document ID: 10148218Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Injector Replacement. INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this problem.
Associated Products (58)Associated Documents - July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148132Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE
- Mfr Comm. #:
- 660414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
Associated Products (94)Associated Documents