BMW 328d Service Bulletins (2015)
442 manufacturer communications on file.
- December 1, 2014•Document ID: 10148175Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 180214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDual Mass Flywheel - Diagnosis and Inspection. INFORMATION The following three criteria must be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload.
Associated Products (3)Associated Documents - December 1, 2014•Document ID: 10148174Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 161614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Engine Soon Light (MIL) is On with SCR Fault 805220 Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32°F / 0°C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. Unfavorable SCR software
Associated Products (7)Associated Documents - December 1, 2014•Document ID: 10148173Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 161514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
Associated Products (106)Associated Documents - December 1, 2014•Document ID: 10148168Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; POWER TRAIN
- Mfr Comm. #:
- 123314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (30)Associated Documents - November 1, 2014•Document ID: 10148429Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK
- Mfr Comm. #:
- 660914
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryUnlocking Trunk with Remote Unlocks All Doors. After programming the vehicle with ISTA/P 2.47.1, unlocking the trunk with the remote changes to unlocking all the doors. An application error occurred after programming the vehicle to the Personal Profile Setting (PIA) in the Front Electronic Module (FEM).
Associated Products (22)Associated Documents - November 1, 2014•Document ID: 10148423Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (138)Associated Documents - November 1, 2014•Document ID: 10148420Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 513114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadlight Cleaning System: Functional Operation Change. The customer complains that the headlight cleaning system is not working properly and only works after several actuating attempts. CAUSE The "functional" operation of the headlight cleaning system was changed with integration level F020-14-07-500. The functional changes to the headlight cleaning system's operation will occur only after programming the vehicle with ISTA/P 2.53.0 or higher. INFORMATION The headlight cleaning system is no longer activated with the first stalk activation when the lights are on. The functional programming change now requires the stalk to be activated four times before headlight cleaning is activated. The change prevents automatic activation of headlight cleaning when the customer only wants to clean his/her windshield. This is normal operation and no parts should be changed.
Associated Products (24)Associated Documents - October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149381Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660814
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummarySide View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
Associated Products (101)Associated Documents - October 1, 2014•Document ID: 10149379Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
Associated Products (53)Associated Documents - October 1, 2014•Document ID: 10149375Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 620414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Instrument Cluster. The display in the instrument cluster is inoperative.
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149371Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 612614
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHorn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: "8044A3 - Wiring, horn short circuit to earth" "8044A4 - Wiring, horn short circuit to positive" "8044A5 - Wiring, horn relay is defective or short circuit to positive" Water has entered the horn and caused it to fail internally (shorted out).
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149365Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryPower-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues. The following codes may be stored in the fault memory of the Electric Power Steering (EPS): Scenario 1: 0x4823E1 Scenario 2: 0x4823CB/0x4823CC Scenario 3: 0x4823D2 and/or 0x4823EC Scenario 4: 0x48239C (DSC warning lamp lights up in the instrument cluster) Scenario 5: No communication with the EPS is possible (not accessible using diagnostics) Scenario 6: 0x4823EE and 0x4823C2
Associated Products (24)Associated Documents - October 1, 2014•Document ID: 10149363Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryFront Suspension Ride Height Has Dropped. INFORMATION Damages due to outside influences are not covered under the terms of the BMW limited warranties.
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149355Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130514
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
Associated Products (58)Associated Documents - October 1, 2014•Document ID: 10149353Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 130114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
Associated Products (20)Associated Documents - October 1, 2014•Document ID: 10149351Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 122914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryReduced Engine Performance. When driving with high outside ambient temperatures, repeated stop and go, or high-load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances, the compressor is switched off. One or both of the following faults are stored in the DME: 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault 241400: Electric fan, diagnosis feedback 1: Fan slightly stiff The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 600W electric fan over-boost or high speed function 2. The electric cooling fan design was not robust enough for continuous over-boost or high-speed operation.
Associated Products (18)Associated Documents - October 1, 2014•Document ID: 10149282Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 111414
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryEngine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
Associated Products (93)Associated Documents - September 1, 2014•Document ID: 10148042Service Bulletin/Repair InstructionsVISIBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 660714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTop Rear Side View Camera Control Unit Rattles While Driving. While driving, a rattling-type noise is heard coming from the lower windshield area up behind the instrument panel (driver's side). CAUSE The TRSVC (Top Rear Side View Camera) control module support bracket is loose.
Associated Products (22)Associated Documents - September 1, 2014•Document ID: 10148032Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- 512614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Service Action: Remove Front Bumper Air Inlet Panel. The front air cooling duct does not cool sufficiently. It may cause the engine to overheat, resulting in a Check Control message. Certain vehicles were manufactured with a ""sealed-off"" front air cooling duct. AFFECTED VEHICLES This Service Action involves F30 vehicles produced from June 26, 2014 to July 4, 2014. First check if a Service Action label with a code number 705 is already attached to the B-pillar. If a code number 705 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Associated Products (10)Associated Documents