Mercedes-Benz A-Class Service Bulletins (2020)
274 manufacturer communications on file.
- September 28, 2024•Document ID: 11008091Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.70-P-077433
- Date Added:
- September 28, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents - September 21, 2024•Document ID: 11007974Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078307
- Date Added:
- September 24, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents - September 20, 2024•Document ID: 11007972Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.60-P-077495
- Date Added:
- September 24, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
Associated Products (31)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz A-Class+ 11 moreAssociated Documents - September 16, 2024•Document ID: 11008056Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI07.70-P-078078
- Date Added:
- September 26, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
Associated Products (40)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz A-Class+ 20 moreAssociated Documents - September 11, 2024•Document ID: 11007796Service Bulletin/Repair InstructionsVISIBILITY/WIPER; ELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.85-P-078303
- Date Added:
- September 14, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
Associated Products (45)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class+ 25 moreAssociated Documents - September 10, 2024•Document ID: 11008323Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078302
- Date Added:
- October 3, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
Associated Products (119)2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class+ 99 moreAssociated Documents - September 10, 2024•Document ID: 11007753Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078301
- Date Added:
- September 13, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents - August 14, 2024•Document ID: 11006700Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- LI82.85-P-077242
- Date Added:
- August 30, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
Associated Products (36)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class+ 16 moreAssociated Documents - July 23, 2024•Document ID: 11005294Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- LI82.10-P-078069
- Date Added:
- July 27, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
Associated Products (263)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 moreAssociated Documents - July 17, 2024•Document ID: 11005313Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- LI07.70-P-078047
- Date Added:
- July 30, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
Associated Products (40)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz A-Class+ 20 moreAssociated Documents - July 15, 2024•Document ID: 11005334Service Bulletin/Repair InstructionsSERVICE BRAKES; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
- Mfr Comm. #:
- LI46.10-P-078012
- Date Added:
- July 30, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
Associated Products (57)2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class+ 37 moreAssociated Documents - July 12, 2024•Document ID: 11005292Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- LI46.35-P-075129
- Date Added:
- July 27, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Vibrations in steering at speeds lower than 50 km/h when turning left and right or while at a stop. May be perceived as a noise from the transmission. Cause Controller instability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Remedy Software A 247 902 11 16 available in Xentry with latest add-ons.
Associated Products (17)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz GLB-Class2019 Mercedes-Benz A-ClassAssociated Documents - July 10, 2024•Document ID: 11005288Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI35.31-P-077429
- Date Added:
- July 27, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryComplaint Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, 247476 247747, 247646 247647 the following applies: • If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. • If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, 247751 247753, 274651 the following applies: • If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part.
Associated Products (17)2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz CLA-Class2019 Mercedes-Benz A-ClassAssociated Documents - May 7, 2024•Document ID: 11000596Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- LI35.31-P-077429
- Date Added:
- May 31, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryInstrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, the following applies: • If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. • If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, the following applies: • If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. • If one of the part numbers A2473502702; A2473502503; A2473504504 has been installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced.
Associated Products (18)2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz GLB-Class2019 Mercedes-Benz A-ClassAssociated Documents - May 4, 2024•Document ID: 11000546Service Bulletin/Repair InstructionsSTEERING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- LI46.35-P-075129
- Date Added:
- May 30, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryVibrations in steering at speeds lower than 50 km/h, possible when turning both in and back, also partly noticeable after changing to winter tires. Controller instability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Software A 247 902 11 16 available in Xentry with latest add-ons.
Associated Products (18)2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz GLB-Class2019 Mercedes-Benz A-ClassAssociated Documents - April 30, 2024•Document ID: 10253708Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- CL - 240401
- Date Added:
- May 1, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryIn our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
Associated Products (17)2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz GLA-Class2020 Mercedes-Benz GLB-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class2019 Mercedes-Benz A-Class2019 Mercedes-Benz CLA-Class2019 Mercedes-Benz GLA-Class2019 Mercedes-Benz GLE-Class2019 Mercedes-Benz GLS-ClassAssociated Documents - April 26, 2024•Document ID: 10253703Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- OTA - 20240402
- Date Added:
- May 1, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryThis is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
Associated Products (56)2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT+ 36 moreAssociated Documents - April 23, 2024•Document ID: 10253715Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- LI47.20-P-071172
- Date Added:
- May 1, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryCheck engine light active and FC P146364 Temp. and pressure sensor B4/7 is stored in Engine control unit and Fuel pump control unit. Software parameter in Fuel pump control unit. Perform software update for Fuel System Control Module (FSCM) N118. New software is A0009026661.
Associated Products (10)Associated Documents - April 12, 2024•Document ID: 10253706Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- EW - FSCM SW
- Date Added:
- May 1, 2024
- Manufacturer:
- MERCEDES-BENZ
SummaryIMPORTANT EMISSION EXTENDED WARRANTY INFORMATION In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the Fuel System Control Module (FSCM) software in certain Model Year ("MY") vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the FSCM software for the fuel pressure sensor and fuel temperature plausibility check may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ("MIL") might illuminate. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P146264 The sensor Low fuel pressure and fuel temperature has a malfunction. There is an implausible signal. -and/or- P146364 This error code can be ignored and erased. 'OR' Sensor Low fuel pressure and fuel temperature has a malfunction during calculation of the fuel pressure. There is an implausible signal. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 47045 90 Control Unit, Fuel Pump - Software Parts (Software): A0009026661 Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty. No part replacement is covered by this extended warranty.
Associated Products (10)Associated Documents - March 11, 2024•Document ID: 10252777Service Bulletin/Repair InstructionsSTRUCTURE:BODY:TRUNK LID; ELECTRICAL SYSTEM:PROPULSION SYSTEM:FUEL CELL; STRUCTURE:BODY:HOOD; STRUCTURE
- Mfr Comm. #:
- LI72.20-P-075746
- Date Added:
- April 5, 2024
- Manufacturer:
- MERCEDES-MAYBACH
SummaryTailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
Associated Products (57)2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class+ 37 moreAssociated Documents