Ford Focus Service Bulletins (2014)
162 manufacturer communications on file.
- September 19, 2018•Document ID: 10149765Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 47528
- Date Added:
- December 3, 2018
- Manufacturer:
- FORD
SummarySome 2012-2018 Focus BEV vehicles may exhibit DTC U0130 in the battery electric control module (BECM) after replacement of the high voltage (HV) battery pack. In order to correct the condition, perform a programmable module installation (PMI) using the appropriate Ford scan tool. This action will initiate a coordinated flash of powertrain control module (PCM) and transmission control module (TCM) for HV battery compatibility. The use of a previous session may also cause DTC U1030 to be present in the BECM. For additional information refer to 2015 or newer Workshop Manual (WSM), Section 414-03A
Associated Products (7)Associated Documents - August 13, 2018•Document ID: 10144937Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- SSM 47462
- Date Added:
- September 24, 2018
- Manufacturer:
- FORD
Summary2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
Associated Products (26)2018 Ford Edge2018 Ford Escape2018 Ford Focus2018 Ford Fusion2018 Lincoln MKC2018 Lincoln MKZ2017 Ford Edge2017 Ford Escape2017 Ford Focus2017 Ford Fusion2017 Lincoln MKC2017 Lincoln MKZ2016 Ford Edge2016 Ford Escape2016 Ford Focus2016 Ford Fusion2016 Lincoln MKC2016 Lincoln MKZ2015 Ford Edge2015 Ford Escape+ 6 moreAssociated Documents - July 20, 2018•Document ID: 10144217Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 47428
- Date Added:
- September 10, 2018
- Manufacturer:
- FORD
SummarySome 2013-2018 Fusion Energi, 2012-2018 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 110.03 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
Associated Products (16)Associated Documents - July 20, 2018•Document ID: 10144195Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT
- Mfr Comm. #:
- tsb18-2216
- Date Added:
- September 10, 2018
- Manufacturer:
- FORD
SummarySome 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
Associated Products (16)Associated Documents - March 30, 2018•Document ID: 10137113Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- SSM 47201
- Date Added:
- May 21, 2018
- Manufacturer:
- FORD
SummaryReplacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
Associated Products (234)2018 Ford C-Max2018 Ford Ecosport2018 Ford Edge2018 Ford Escape2018 Ford Explorer2018 Ford F-1502018 Ford Fiesta2018 Ford Flex2018 Ford Fusion2018 Ford Mustang2018 Ford Taurus2018 Ford Transit2018 Lincoln Continental2018 Lincoln MKC2018 Lincoln MKT2018 Lincoln MKX2018 Lincoln MKZ2017 Ford C-Max2017 Ford Edge2017 Ford Escape+ 214 moreAssociated Documents - March 29, 2018•Document ID: 10137110Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 47198
- Date Added:
- May 21, 2018
- Manufacturer:
- FORD
SummarySome 2013-2017 Fusion Energi, 2012-2017 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
Associated Products (16)Associated Documents - March 15, 2018•Document ID: 10137097Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 47161
- Date Added:
- May 21, 2018
- Manufacturer:
- FORD
SummarySome 2012-2017 Focus BEV, 2013-2016 Fusion Energi And 2013-2017 CMAX Energi vehicles equipped with a Telematics Control Unit (TCU) may exhibit inoperative remote features via My Ford Mobile app, discharged battery, incomplete user authorization and/or diagnostic trouble code (DTC) U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If DTC U0198 remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
Associated Products (15)Associated Documents - March 5, 2018•Document ID: 10137085Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- SSM 47130
- Date Added:
- May 21, 2018
- Manufacturer:
- FORD
SummarySome 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
Associated Products (18)Associated Documents - February 20, 2018•Document ID: 10136582Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- TSB18-2062
- Date Added:
- May 14, 2018
- Manufacturer:
- FORD
SummarySome 2012-2014 Focus vehicles equipped with a 2.0L gasoline direct injection (GDI) engine may exhibit concerns of engine runs rough, crank no-start, loss of power, loss of engine RPM, and/or illuminated MIL with diagnostic trouble codes (DTCs) P0122, P0222, P0320, P0322, P0327, P0332, P0344, P0369, P06A7, P060D, P061C, P1336, P1674, P2111, P2112, P2127 and/or P2135. Follow the Service Procedure steps to correct the condition.
Associated Products (3)Associated Documents - February 14, 2018•Document ID: 10136597Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- SSM 47080
- Date Added:
- May 14, 2018
- Manufacturer:
- FORD
Summary2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
Associated Products (199)2018 Ford Edge2018 Ford Escape2018 Ford Explorer2018 Ford F-1502018 Ford F-2502018 Ford F-3502018 Ford Fiesta2018 Ford Flex2018 Ford Focus2018 Ford Fusion2018 Ford Mustang2018 Ford Taurus2018 Ford Transit2018 Lincoln Continental2018 Lincoln MKC2018 Lincoln MKT2018 Lincoln MKX2018 Lincoln MKZ2017 Ford C-Max2017 Ford Edge+ 179 moreAssociated Documents - January 17, 2018•Document ID: 10140286Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- TSB18-2009
- Date Added:
- June 11, 2018
- Manufacturer:
- FORD
SummarySome 2013-2016 Focus Electric vehicles built on or after 22-Feb-2013 may exhibit an illuminated green ready to drive indicator in the instrument panel cluster (IPC) and the vehicle does not move. The condition may occur when the vehicle is restarted within 20 seconds after being powered off, starting the vehicle within 20 seconds of unplugging or starting the vehicle 15 minutes after being remotely started. Follow the Service Procedure steps to correct the condition.
Associated Products (4)Associated Documents - January 17, 2018•Document ID: 10138487Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- TSB18-2009
- Date Added:
- May 29, 2018
- Manufacturer:
- FORD
SummarySome 2013-2016 Focus Electric vehicles built on or after 22-Feb-2013 may exhibit an illuminated green ready to drive indicator in the instrument panel cluster (IPC) and the vehicle does not move. The condition may occur when the vehicle is restarted within 20 seconds after being powered off, starting the vehicle within 20 seconds of unplugging or starting the vehicle 15 minutes after being remotely started. Follow the Service Procedure steps to correct the condition.
Associated Products (4)Associated Documents - January 10, 2018•Document ID: 10140323Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT
- Mfr Comm. #:
- SSM 47009
- Date Added:
- June 11, 2018
- Manufacturer:
- FORD
SummaryThe Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
Associated Products (180)2018 Ford C-Max2018 Ford Edge2018 Ford Escape2018 Ford Explorer2018 Ford F-1502018 Ford Fiesta2018 Ford Flex2018 Ford Focus2018 Ford Fusion2018 Ford Taurus2018 Ford Transit2017 Ford C-Max2017 Ford Edge2017 Ford Escape2017 Ford Expedition2017 Ford Explorer2017 Ford F-1502017 Ford Fiesta2017 Ford Flex2017 Ford Focus+ 160 moreAssociated Documents - January 10, 2018•Document ID: 10138524Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- SSM 47009
- Date Added:
- May 29, 2018
- Manufacturer:
- FORD
SummaryThe Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
Associated Products (277)2018 Ford C-Max2018 Ford E-3502018 Ford E-4502018 Ford Edge2018 Ford Escape2018 Ford Explorer2018 Ford F-1502018 Ford F-2502018 Ford F-3502018 Ford F-6502018 Ford F-7502018 Ford Fiesta2018 Ford Flex2018 Ford Focus2018 Ford Fusion2018 Ford Taurus2018 Ford Transit2017 Ford C-Max2017 Ford E-2502017 Ford E-350+ 257 moreAssociated Documents - November 3, 2017•Document ID: 10127394Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 17-2218
- Date Added:
- January 29, 2018
- Manufacturer:
- FORD
SummarySome 2013-2018 Escape, Focus and C-Max vehicles may exhibit a water stained headliner after the vehicle has experienced a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.
Associated Products (18)Associated Documents - November 2, 2017•Document ID: 10127405Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- SSM 46900
- Date Added:
- January 29, 2018
- Manufacturer:
- FORD
SummarySome vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Associated Products (202)2018 Ford Edge2018 Ford Escape2018 Ford Explorer2018 Ford F-1502018 Ford Fiesta2018 Ford Flex2018 Ford Focus2018 Ford Fusion2018 Ford Mustang2018 Ford Transit2018 Lincoln Continental2018 Lincoln MKC2018 Lincoln MKT2018 Lincoln MKZ2017 Ford C-Max2017 Ford E-2502017 Ford E-3502017 Ford E-4502017 Ford Edge2017 Ford Escape+ 182 moreAssociated Documents - September 13, 2017•Document ID: 10119670Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- SSM 46814
- Date Added:
- October 21, 2017
- Manufacturer:
- FORD
SummarySome 2014-2017 Focus ST vehicles equipped with a 2.0L gasoline turbocharged direct injection (GTDI) engine may exhibit an audible engine idle ticking noise at normal operating temperature. This is considered a normal operating characteristic and no repair should be attempted.
Associated Products (4)Associated Documents - April 26, 2017•Document ID: 10109023Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- SSM 46545
- Date Added:
- August 1, 2017
- Manufacturer:
- FORD
SummarySome 2014-2017 Focus/C-MAX vehicles when a replacement BCM is received for a service repair may include a white Keyless Entry Card. In an effort to consolidate the complexity of BCM's only the highest level will be available for service. If the vehicle has the Keyless Entry buttons on the left door B-pillar the card needs to stay with the vehicle and shared with the customer as the keyless entry codes have changed. If the vehicle was not built with the b-pillar touch pad, discard the card, as it has no function, and cannot be added to the vehicle. If the vehicle has the stick-on wireless key pad, that keypad has it's own card, and again discard the one that came with the service BCM.
Associated Products (8)Associated Documents - April 14, 2017•Document ID: 10109018Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- SSM 46534
- Date Added:
- August 1, 2017
- Manufacturer:
- FORD
SummarySome 2013-2017 Fusion Hybrid Energi built on or before 24-Mar-2017, 2012-2016 Focus Electric and 2013-2016 C-MAX Energi and equipped with a TCU may exhibit inoperative remote features via MyFord Mobile app, discharged battery, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU field service actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 104.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
Associated Products (14)Associated Documents - March 2, 2017•Document ID: 10099106Service Bulletin/Repair InstructionsPOWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
- Mfr Comm. #:
- SSM 46421
- Date Added:
- May 15, 2017
- Manufacturer:
- FORD
Summary2013-2017 FOCUS S MODEL VEHICLES DO NOT HAVE AN OUTSIDE AMBIENT TEMPERATURE DISPLAYED IN THE IPC AND THIS FEATURE CANNOT BE ADDED. THE SENSOR IS IN THE RIGHT HAND OUTSIDE MIRROR AND IS USED BY THE POWERTRAIN CONTROL MODULE (PCM) FOR CALCULATIONS.
Associated Products (5)Associated Documents