BMW M235i Service Bulletins (2015)
319 manufacturer communications on file.
- February 1, 2016•Document ID: 10151098Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; EQUIPMENT
- Mfr Comm. #:
- B360115
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySI B36 01 15 February 2016 Wheel and Tires Technical Service This Service Information bulletin supersedes SI 36 01 15 dated October 2015. designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Associated Products (66)Associated Documents - February 1, 2016•Document ID: 10151079Service Bulletin/Repair InstructionsEQUIPMENT; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
Associated Products (213)Associated Documents - February 1, 2016•Document ID: 10151077Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN
- Mfr Comm. #:
- B123314
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI 12 33 14 dated December 2015. SUBJECT Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (60)Associated Documents - January 1, 2016•Document ID: 10151029Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B840815
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"?SUBJECT During the QC1 the BMW Assist Test Call Fails . After the transport mode is deleted (during the QC1), a BMW Assist (SOS) test call is made by pressing the SOS/ E-Call button. However, the call only connects via voice (no data is transmitted). The operator indicates that a crash call has been sent. ATM fault code ""B7F348 - Provisioning without signature OTA"" is stored. The provisioning of the ATM (Advanced Telematics Module) has failed."
Associated Products (55)Associated Documents - January 1, 2016•Document ID: 10151027Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- B652515
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary?SUBJECT Incremental Map Update of the NBT EVO Head Unit . Customers may be receiving onscreen messages concerning updates of their navigation system. Database mapping procedure in vehicles with the NBT EVO Head Unit (Head Unit high 2) has been changed to automatic, periodic, Over- the-Air (OTA), regional, incremental updates. INFORMATION Customers may not be familiar with the messages seen prior to, during, and after this update which may prompt inquiries. The following information provides an overview of the automatic OTA process that has replaced the previously required BMW center visit for navigation map updates. UPDATE DETAILS Updates can occur up to 4 times per year, ensuring that customers have the newest map data available. At a minimum, updates occur during first 2 years of vehicle ownership at no additional charge to the customer. At additional customers expense updates can also occur for up to 4 years (depending upon vehicle retail date and BMW assist options selected). Please check the BMW connected drive service cockpit for details on an individual vehicles coverage. To access the BMW connected drive service cockpit refer to the attachment.
Associated Products (48)Associated Documents - January 1, 2016•Document ID: 10151025Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT
- Mfr Comm. #:
- B651313
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"?This Service Information bulletin supersedes SI B65 13 13 dated October 2014. SUBJECT Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed . Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Note: If Fault Code E1C440 ""Headunit Reset"" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H."
Associated Products (50)Associated Documents - January 1, 2016•Document ID: 10151023Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B650709
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryWhistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
Associated Products (289)Associated Documents - January 1, 2016•Document ID: 10151022Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640915
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryWhistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
Associated Products (42)Associated Documents - January 1, 2016•Document ID: 10151018Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B620316
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary?Clock gains or loses time. The time displayed in the KOMBI (instrument cluster) may gain or lose a few minutes each week. Internal KOMBI calculation error.
Associated Products (57)Associated Documents - January 1, 2016•Document ID: 10151016Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- B620116
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement."
Associated Products (55)Associated Documents - January 1, 2016•Document ID: 10150905Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; EQUIPMENT
- Mfr Comm. #:
- B161514
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummarySI B16 15 14 January 2016 Fuel Supply Systems Technical Service.This Service Information bulletin supersedes SI B16 15 14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.
Associated Products (103)Associated Documents - December 1, 2015•Document ID: 10147888Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT
- Mfr Comm. #:
- B651915
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryXM Satellite Radio Reception. INFORMATION Currently Satellite Radio is provided by SiriusXM for BMW customers. SiriusXM is the only company currently broadcasting Satellite Radio in North America. Satellite radio is broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which currently come in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units will move to the XM Satellites constellation and will show the same location based cutouts. SiriusXM is currently updating the repeater network to cover areas of low reception, but the general disadvantage of geostationary satellites can't be compensated completely. Buildings, hills, trees, highway sound blocking walls or any other obstacles might block the satellite signal coming from the south at a 32 degree elevation angle and might cause audio cut outs in absence of terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets flatter. Adverse weather conditions will affect reception. Sirius XM will increase the amount of Sirius and XM repeaters gradually to improve situation in metropolitan areas. When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Do not compare an XM equipped vehicle to a Sirius equipped vehicle. Replace no parts Customers should direct all reception complaints to one of the following: BMW Customer Relations department at either 1-800-831-1117 or [email protected] BMW Genius Hotline 1-844-443-6487 or to the dealers onsite BMW Genius Customers must provide the exact location (street address or Latitude/Longitude), weathe
Associated Products (35)Associated Documents - December 1, 2015•Document ID: 10147884Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
- Mfr Comm. #:
- B621215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryInstrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
Associated Products (126)Associated Documents - December 1, 2015•Document ID: 10147881Service Bulletin/Repair InstructionsVISIBILITY:WINDSHIELD WIPER/WASHER
- Mfr Comm. #:
- B612315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."
Associated Products (39)Associated Documents - December 1, 2015•Document ID: 10147872Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- B340814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?SI B34 08 14 Brakes December 2015 Technical Service This Service Information bulletin supersedes SI 34 08 14 dated July 2015. designates changes to this revision SUBJECT Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
Associated Products (34)Associated Documents - December 1, 2015•Document ID: 10147863Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B123314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (42)Associated Documents - November 1, 2015•Document ID: 10147833Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B650915
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
Associated Products (132)Associated Documents - October 1, 2015•Document ID: 10147775Service Bulletin/Repair InstructionsSTRUCTURE:BODY:ROOF AND PILLARS
- Mfr Comm. #:
- B513315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"The left A-pillar/bulkhead joint may be leaking. AFFECTED VEHICLES The joint of the bulkhead plate and A-pillar reinforcement is supposed to be sealed with an adhesive strip and a PVC seam.The PVC seam was not applied correctly in places and can cause leaks. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. The joint of the bulkhead plate and A-pillar reinforcement is supposed to be sealed with an adhesive strip and a PVC seam.The PVC seam was not applied correctly in places and can cause leaks."
Associated Products (6)Associated Documents - October 1, 2015•Document ID: 10147773Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE:BODY
- Mfr Comm. #:
- B513115
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Vehicles were built without the Universal Garage Door Opener (UGDO) Mirror and are missing option code 319 (Integrated universal remote control) from the vehicle order. AFFECTED VEHICLES This Service Action affects F22 vehicles produced from July 1, 2015 to August 26, 2015. Vehicles requiring the retrofit will display the following ""Vehicle Comment"" In the DCSnet ""Warranty Vehicle Inquiry: Universal Garage Door Opener Mirror retrofit repair (option code SA319) applies to this vehicle, please see SI B51 31 15. If this vehicle already had the retrofit repair performed, no further action is required."
Associated Products (4)Associated Documents - October 1, 2015•Document ID: 10147771Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- B360115
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Associated Products (43)Associated Documents