BMW ActiveHybrid 7 Service Bulletins (2012)
280 manufacturer communications on file.
- July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148133Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 660514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySpeed Limit Information Does Not Work. Speed limit information (SLI) is not displayed in the Kombi or the Head-Up Display (HUD). This only affects the specific VINs (vehicle identification numbers) listed below. The vehicle was built incorrectly (without option 8TH).
Associated Products (24)2015 BMW 740Li2015 BMW 750Li2015 BMW 760Li2015 BMW ActiveHybrid 32015 BMW R nineT2014 BMW 740Li2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72013 BMW 740Li2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW F 800 R2012 BMW 740Li2012 BMW 750Li2012 BMW 760Li2012 BMW ActiveHybrid 72011 BMW 740Li2011 BMW 750Li2011 BMW 760Li+ 4 moreAssociated Documents - July 1, 2014•Document ID: 10148132Service Bulletin/Repair InstructionsFORWARD COLLISION AVOIDANCE
- Mfr Comm. #:
- 660414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFront Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
Associated Products (94)Associated Documents - July 1, 2014•Document ID: 10148130Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SEATS
- Mfr Comm. #:
- 652113
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryWhen Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
Associated Products (78)Associated Documents - July 1, 2014•Document ID: 10148128Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 650214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
Associated Products (81)Associated Documents - July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - June 1, 2014•Document ID: 10148101Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Associated Products (215)Associated Documents - June 1, 2014•Document ID: 10148096Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- 360314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRDC: Incorrect Tire Position Displayed with Air Pressure Drop. When there is a low tire pressure warning, in some cases the position of the affected tire may be incorrectly displayed in the instrument cluster and CD (Control Display). Software error in the RDC (tire pressure control) module in conjunction with wheel electronics part number 4 078 787 or 4 079 152.
Associated Products (24)Associated Documents - May 1, 2014•Document ID: 10148333Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCondition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
Associated Products (79)Associated Documents - May 1, 2014•Document ID: 10148315Service Bulletin/Repair InstructionsSERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS
- Mfr Comm. #:
- 340213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
Associated Products (57)Associated Documents - May 1, 2014•Document ID: 10148312Service Bulletin/Repair InstructionsSUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE; SUSPENSION:FRONT:WHEEL BEARING
- Mfr Comm. #:
- 310112
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (70)Associated Documents - May 1, 2014•Document ID: 10148308Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (82)Associated Documents - March 1, 2014•Document ID: 10148010Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Associated Products (211)Associated Documents - March 1, 2014•Document ID: 10147923Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 612213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"""Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
Associated Products (58)Associated Documents - February 1, 2014•Document ID: 10147985Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMy BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
Associated Products (66)Associated Documents - February 1, 2014•Document ID: 10147984Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 840613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
Associated Products (94)Associated Documents - February 1, 2014•Document ID: 10147982Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 652313
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
Associated Products (98)Associated Documents - February 1, 2014•Document ID: 10147981Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 650414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Airbag Warning Light: ACSM FC 930A60 Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
Associated Products (88)Associated Documents - February 1, 2014•Document ID: 10147976Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 620613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThe Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Associated Products (88)Associated Documents - February 1, 2014•Document ID: 10147968Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRubbing Noise from Front Axle. A rubbing or creaking noise is heard from the front axle when driving over uneven road surfaces. The vibration dampener in the front axle support is pressing against the front axle support.
Associated Products (34)2015 BMW 740i2015 BMW 740Li2015 BMW 750i2015 BMW 750Li2015 BMW 760Li2015 BMW ActiveHybrid 72014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 72013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 72012 BMW 740i2012 BMW 740Li2012 BMW 750i+ 14 moreAssociated Documents