BMW ActiveHybrid 5 Service Bulletins (2013)
369 manufacturer communications on file.
- April 1, 2014•Document ID: 10148256Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE
- Mfr Comm. #:
- 121712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN52T / N55 with 8HP45: Delay in Engine Response. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
Associated Products (31)Associated Documents - April 1, 2014•Document ID: 10148254Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL
- Mfr Comm. #:
- 120214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Program Control Units (Fuel Shut-off Valve). Due to a software error, it is possible that a Check Engine light (MIL) may not be illuminated after a fault is detected at the fuel shut-off valve (TAV). This is an emissions-relevant fault.
Associated Products (7)Associated Documents - April 1, 2014•Document ID: 10148252Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 120113
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Transmission Intermittently Goes into ""P"" or ""N"" After MSA Engine Start. After an MSA engine start, the transmission intermittently goes into the Park (P) or Neutral (N) position without any customer influence. This problem can be sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software"
Associated Products (23)2014 BMW 535i2014 BMW 640i2013 BMW 320i2013 BMW 328i2013 BMW 335i2013 BMW 528i2013 BMW 535i2013 BMW 640i2013 BMW 740i2013 BMW 740Li2013 BMW ActiveHybrid 32013 BMW ActiveHybrid 52013 BMW ActiveHybrid 72013 BMW X32012 BMW 328i2012 BMW 335i2012 BMW 528i2012 BMW 535i2012 BMW 640i2012 BMW ActiveHybrid 5+ 3 moreAssociated Documents - April 1, 2014•Document ID: 10148251Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE
- Mfr Comm. #:
- 110514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryS63TU Engine: Noises from Leaking Exhaust Manifold. A rattling, knocking, clattering or hissing noise can be heard from the engine compartment while the engine is running. It is more pronounced when the engine is under load. CAUSE The exhaust manifold attaching screws have come loose, causing an exhaust leak.
Associated Products (13)Associated Documents - March 1, 2014•Document ID: 10147921Service Bulletin/Repair InstructionsWHEELS
- Mfr Comm. #:
- 360114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFitting Winter Tires Properly to Vehicles with Ceramic Brakes. Wheel studs may loosen after wheels for the rear axle are incorrectly fitted to the front axle on vehicles equipped with option 2NK (ceramic brakes). Incorrect installation of rear axle winter tires (wheel style 409M) onto the front axle in conjunction with ceramic brakes
Associated Products (33)Associated Documents - March 1, 2014•Document ID: 10147918Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 130413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION There is an error in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. The vehicle may also exhibit rough running at idle and while driving. F07 and F10: P/N 13 64 7 639 994 is for all vehicles produced from 7/2014 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2014 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 F06, F12 and F13: P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 Until further notice, it is good practice to verify that the injector part number being removed from the engine matches the new injector part number. Always review the vehicle history to identify if the injectors have already been replaced. When the ETK data is corrected, a notification will be distributed. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16028.3.B130413... 4/24/2014
Associated Products (35)Associated Documents - January 1, 2014•Document ID: 10147955Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryMy BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
Associated Products (37)Associated Documents - January 1, 2014•Document ID: 10147946Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- 630514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. CAUSE Software error in TMS 3 (Headlight driver module AHL xenon light)"
Associated Products (38)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents - January 1, 2014•Document ID: 10147706Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
Associated Products (54)Associated Documents - November 1, 2013•Document ID: 10150185Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 651813
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryTouchpad Integrated in the iDrive Controller Is Intermittently Inoperative. Intermittently the Touchpad integrated in the iDrive controller is inoperative. * No entries can be made using the Touchpad * Fault code is stored in the touch-box control unit Software error in the touch-box control unit (TBX)
Associated Products (38)Associated Documents - November 1, 2013•Document ID: 10150183Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 630713
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryDaytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
Associated Products (41)Associated Documents - November 1, 2013•Document ID: 10150181Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- 612213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"""Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
Associated Products (58)Associated Documents - November 1, 2013•Document ID: 10150171Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; EQUIPMENT
- Mfr Comm. #:
- 511613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryBang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly
Associated Products (55)Associated Documents - November 1, 2013•Document ID: 10150166Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- 340213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryIncorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model.
Associated Products (52)Associated Documents - November 1, 2013•Document ID: 10150161Service Bulletin/Repair InstructionsENGINE; POWER TRAIN
- Mfr Comm. #:
- 121713
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
Associated Products (83)Associated Documents - November 1, 2013•Document ID: 10150159Service Bulletin/Repair InstructionsENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION
- Mfr Comm. #:
- 120113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryMN16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
Associated Products (23)2014 BMW 535i2014 BMW 640i2013 BMW 320i2013 BMW 328i2013 BMW 335i2013 BMW 528i2013 BMW 535i2013 BMW 640i2013 BMW 740i2013 BMW 740Li2013 BMW ActiveHybrid 32013 BMW ActiveHybrid 52013 BMW ActiveHybrid 72013 BMW X32012 BMW 328i2012 BMW 335i2012 BMW 528i2012 BMW 535i2012 BMW 640i2012 BMW ActiveHybrid 5+ 3 moreAssociated Documents - October 1, 2013•Document ID: 10150266Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 651113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryInstallation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
Associated Products (57)Associated Documents - October 1, 2013•Document ID: 10150263Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 640113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"IHKA Operating Panel Buttons Are Peeling. INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the ""Repair kit for button caps"" when performing this repair. Replace ALL the buttons with those included in the kit. Note: Please do not use and claim the part number for the "Repair kit, radio and A/C panel." To ensure the button cap kit with the correct symbols and labels is installed, perform a part number lookup in ETK by VIN. Labor operation code 64 11 326 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 64 11 769 instead."
Associated Products (57)Associated Documents - October 1, 2013•Document ID: 10150257Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (71)Associated Documents