BMW 750i Service Bulletins (2012)
326 manufacturer communications on file.
- December 1, 2012•Document ID: 10150383Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 613812
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. AFFECTED VEHICLES This Service Action involves F01, F02, F04, F06, F07, F10, F12, F13 and F25 vehicles which were produced August 2010 to June 2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."
Associated Products (46)Associated Documents - December 1, 2012•Document ID: 10150373Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- 310412
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryGroaning Noise from Front Axle. Groaning noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or over uneven road surfaces. CAUSE Hydraulic mount in tension strut
Associated Products (32)Associated Documents - December 1, 2012•Document ID: 10150372Service Bulletin/Repair InstructionsSUSPENSION:FRONT
- Mfr Comm. #:
- 310312
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryGroaning Noise from Front Axle. Groaning noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or over uneven road surfaces. CAUSE Hydraulic mount in tension strut
Associated Products (24)Associated Documents - October 1, 2012•Document ID: 10150328Service Bulletin/Repair InstructionsSTRUCTURE
- Mfr Comm. #:
- 512912
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryRattling Noise from the Front Passenger Side Trim. A rattling or clattering noise may be heard from the front passenger's side footwell area when driving on rough roads. CAUSE The front passenger's footwell trim makes contact with the side cover of the instrument panel.
Associated Products (24)2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 72013 BMW F 800 R2012 BMW 740i2012 BMW 740Li2012 BMW 750i2012 BMW 750Li2012 BMW 760Li2012 BMW ActiveHybrid 72011 BMW 740i2011 BMW 740Li2011 BMW 750i2011 BMW 750Li2011 BMW 760Li2011 BMW ActiveHybrid 72011 BMW R 1200 GS2010 BMW 750i+ 4 moreAssociated Documents - October 1, 2012•Document ID: 10150323Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 310112
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (56)Associated Documents - October 1, 2012•Document ID: 10150318Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 130612
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"N63 and N74 Engine: ISTA/D 2.33 Diagnostic Error in the Low-pressure Fuel Supply Sensor Value. INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in ""DME Diagnostic Query"" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select ""DME"" in the control unit tree. 3. Select "" Call Up ECU Functions."" 4. Select ""Diagnostic Query."" 5. Select ""Fuel Pressure (Low Pressure)."" 6. Select ""Query Status."" The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012. "
Associated Products (56)Associated Documents