BMW 750i Service Bulletins (2010)
310 manufacturer communications on file.
- April 1, 2013•Document ID: 10149491Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- 651313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Hardware error in the Headunit-High"
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149488Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 640113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMRed or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
Associated Products (55)Associated Documents - April 1, 2013•Document ID: 10149346Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610313
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
Summary"High Battery Discharge Warning: Battery Needs Replacement. After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: * Unfavorable driving profile - excessive short trips * Excessive terminal 30B after run - normal coolant pump or electric fan operation * Extremely cold temperatures * Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups"
Associated Products (15)Associated Documents - April 1, 2013•Document ID: 10149342Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 340513
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHill Descent Control Inoperative After Programming with ISTA/P 2.49.0 or 2.49.1. Hill Descent Control is inoperative after programming the vehicle with ISTA/P versions 2.49.0. or 2.49.1. Central Gateway Module software error.
Associated Products (34)Associated Documents - April 1, 2013•Document ID: 10149335Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
Associated Products (69)Associated Documents - March 1, 2013•Document ID: 10150132Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 651113
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryCIS Seat Mat Replacement. Installation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
Associated Products (55)Associated Documents - March 1, 2013•Document ID: 10150130Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 651009
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryThe vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (173)Associated Documents - March 1, 2013•Document ID: 10150125Service Bulletin/Repair InstructionsEQUIPMENT; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM
- Mfr Comm. #:
- 640111
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"Whistling Noise Heard from the Center Fresh-Air Vent During Heating. A whistling noise is heard from the center fresh-air vents. The noise can be heard during the warm up phase (3 to 10 mins) after the heating system is first activated, with low outside temperatures and the center vents stratification adjustment wheel is turned to the ""red"" position. Note: This is independent of the air distribution setting, but a lower fan speed is required. CAUSE Unfavorable air flow against the mixing flaps in the upper distribution housing"
Associated Products (32)2013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW ActiveHybrid 72013 BMW M52012 BMW 528i2012 BMW 535i2012 BMW 550i2012 BMW 740i2012 BMW 740Li2012 BMW 750i2012 BMW 750Li2012 BMW 760Li2012 BMW ActiveHybrid 52011 BMW 528i+ 12 moreAssociated Documents - March 1, 2013•Document ID: 10150115Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610313
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
Summary"High Battery Discharge Warning: Battery Needs Replacement. After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: * Unfavorable driving profile - excessive short trips * Excessive terminal 30B after run - normal coolant pump or electric fan operation * Extremely cold temperatures * Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups"
Associated Products (10)Associated Documents - March 1, 2013•Document ID: 10150114Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610211
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryAdvanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (State of Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
Associated Products (68)Associated Documents - March 1, 2013•Document ID: 10150101Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; ENGINE
- Mfr Comm. #:
- 130712
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (71)Associated Documents - March 1, 2013•Document ID: 10150099Service Bulletin/Repair InstructionsFUEL/PROPULSION SYSTEM
- Mfr Comm. #:
- 130213
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
Associated Products (118)Associated Documents - March 1, 2013•Document ID: 10150096Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE
- Mfr Comm. #:
- 121611
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryN55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
Associated Products (134)Associated Documents - March 1, 2013•Document ID: 10038217Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)
- Mfr Comm. #:
- SIB-11-03-08
- Date Added:
- June 11, 2011
- Manufacturer:
- BMW
SummaryBMW: CRANKCASE PRESSURE DIAGNOSIS AND INFORMATION FOR ALL VEHICLES. *RM UPDATED ON 4/24/2013. *KB
Associated Products (97)Associated Documents - February 1, 2013•Document ID: 10149457Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 651412
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHeadunit High: Vehicle Position Is Incorrect on the Navigation Map. The vehicle position on the navigation map is incorrect. With route guidance active, the vehicle is displayed: * In an incorrect location Or * Outside the planned route The navigation system integrated in the Headunit High (HU-H) is not calibrated correctly.
Associated Products (51)2014 BMW 528i2014 BMW 535d2014 BMW 535i2014 BMW 550i2014 BMW 740i2014 BMW 740Li2014 BMW 750i2014 BMW 750Li2014 BMW 760Li2014 BMW ActiveHybrid 32014 BMW ActiveHybrid 72014 BMW M52013 BMW 528i2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 3+ 31 moreAssociated Documents - February 1, 2013•Document ID: 10149452Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 640113
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryIHKA Operating Panel Buttons Are Peeling.
Associated Products (57)Associated Documents - February 1, 2013•Document ID: 10149451Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630413
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryMoisture in LED Headlight.
Associated Products (24)2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 72013 BMW F 800 R2012 BMW 740i2012 BMW 740Li2012 BMW 750i2012 BMW 750Li2012 BMW 760Li2012 BMW ActiveHybrid 72011 BMW 740i2011 BMW 740Li2011 BMW 750i2011 BMW 750Li2011 BMW 760Li2011 BMW ActiveHybrid 72011 BMW R 1200 GS2010 BMW 750i+ 4 moreAssociated Documents - February 1, 2013•Document ID: 10149446Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610211
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryAdvanced Onboard Battery Diagnostics. Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (Stateof Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
Associated Products (72)Associated Documents - January 1, 2013•Document ID: 10149309Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS
- Mfr Comm. #:
- 621012
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryHead-Up Display Is Too Dark. The Head-up Display (HUD) is too dark. Rain/light/solar/condensation sensor (RLSB) hardware error
Associated Products (59)Associated Documents - January 1, 2013•Document ID: 10149300Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM
- Mfr Comm. #:
- 130712
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (69)Associated Documents