BMW 650i Service Bulletins (2012)
363 manufacturer communications on file.
- December 1, 2014•Document ID: 10148173Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 161514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
Associated Products (106)Associated Documents - December 1, 2014•Document ID: 10148172Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 130712
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Associated Products (86)Associated Documents - December 1, 2014•Document ID: 10148165Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- 122114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEngine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated and, while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Vehicles with option 610 (Head-Up Display) are not affected. Follow the ISTA/D test plan for the applicable faults stored in the DME. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling.
Associated Products (36)Associated Documents - December 1, 2014•Document ID: 10148163Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 111614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure to check the engine timing chains for wear and should be completed in conjunction with SI B11 06 14 "N63 Customer Care Package". Performing the test plans identified in the procedure below will detect wear at an early stage and if necessary provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to assure the highest standard of performed repairs.
Associated Products (59)Associated Documents - December 1, 2014•Document ID: 10148162Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThe test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015
Associated Products (76)Associated Documents - December 1, 2014•Document ID: 10148161Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryINFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The procedure described in this bulletin should be completed in conjunction with performing SI B11 16 14, N63 Engine: Check the Timing Chain. Perform all recommended, due or qualifying "time-based" maintenance service tasks as directed by the Key Reader/ISPA Light application. Note: The procedure in SI B11 16 14 includes an engine oil and filter change. When applicable, also perform the procedure described in SI B61 30 14, 12-Volt Battery Replacement under the BMW Maintenance Program together with performing the N63 Customer Care Package. After completing all necessary repairs, vehicle needs to be test driven for up to 30 minutes to assure the highest standard of performed repairs.
Associated Products (59)Associated Documents - November 1, 2014•Document ID: 10148428Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY
- Mfr Comm. #:
- 652013
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryVehicle inTransport Mode Cannot Be Unlocked with Remote Control. When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.
Associated Products (78)Associated Documents - November 1, 2014•Document ID: 10148423Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (138)Associated Documents - November 1, 2014•Document ID: 10148421Service Bulletin/Repair InstructionsSTRUCTURE:BODY; EQUIPMENT:OTHER:LABELS
- Mfr Comm. #:
- 513314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
Associated Products (80)Associated Documents - November 1, 2014•Document ID: 10148417Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 110413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63TU Engine: Engine Oil Consumption. The customer complains that the "low engine oil" message is displayed too frequently. CAUSE The cause is related to, but not limited to, one or more of the following components and systems shown below: z Turbocharger z Crankcase ventilation z Engine gasket leaks z Internal engine tolerances and sealing z Improper filling or topping up Use the troubleshooting procedure below to help identify the cause.
Associated Products (19)Associated Documents - October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149381Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660814
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummarySide View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
Associated Products (101)Associated Documents - October 1, 2014•Document ID: 10149380Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 651914
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDWA Siren Malfunction. When the anti-theft alarm (DWA) is triggered, the horn comes on instead of the alarm siren. DWA internal monitoring is too sensitive.
Associated Products (15)Associated Documents - October 1, 2014•Document ID: 10149378Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 631114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryLED Low Beam Flashes Briefly After Ignition Switched ON. 1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)
Associated Products (78)Associated Documents - October 1, 2014•Document ID: 10149361Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 280114
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDCT Transmission: Oil Leakage Diagnosis. INFORMATION Incorrect diagnosis of DCT (Double-clutch Transmission) oil leaks may lead to unnecessary part replacements and repeat customer repair visits. When diagnosing complaints related to DCT fluid leaks, please use the attached diagnostic procedure. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B280114_DCT_Oil_Leak_Diagnosis. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16672.2.B28011... 12/24/2014
Associated Products (63)Associated Documents - October 1, 2014•Document ID: 10057568Service Bulletin/Repair InstructionsEXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH
- Mfr Comm. #:
- SIB-63-11-14
- Date Added:
- June 10, 2015
- Manufacturer:
- BMW
SummaryBMW: ON SOME VEHICLES, WHEN STARTING, LOW BEAM, WITH 0552 OPTION, WOULD BRIEFLY FLASHES, DUE TO A FAULTY LED MAIN LIGHT MODULE THAT NEEDS REPLACING. MODEL 2008-14 F01, F02, F06, F07, F10, F12, F13, F25. *PE
Associated Products (95)Associated Documents - September 1, 2014•Document ID: 10148022Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 122514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN63T: Improvements to Bosch Spark Plug. Various engine performance symptoms could occur if the spark plug insulator becomes damaged: * The Service Engine Soon (MIL) may be on with rough running and misfire fault(s) stored. * Intermittent performance or rough running without a relevant DME fault stored. The spark plug insulator could be damaged in cases of combustion faults such as misfiring, ignition knock or super knocking conditions.
Associated Products (22)Associated Documents - August 1, 2014•Document ID: 10148226Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- 511613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly.
Associated Products (67)Associated Documents - July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148134Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- 660614
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryRear View Camera Does Not Display Image on CID. After engaging the reverse gear, the reversing camera does not display a picture in the CID (Central Information Display). CAUSE The drive mechanism for the roundel actuation in the boot lid is faulty.
Associated Products (12)Associated Documents