BMW 545i Service Bulletins (2005)
55 manufacturer communications on file.
- May 1, 2015•Document ID: 10147123Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - February 1, 2015•Document ID: 10147067Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 070314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - January 1, 2015•Document ID: 10147624Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 651009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Associated Products (222)Associated Documents - January 1, 2015•Document ID: 10147623Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 650509
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryThis Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
Associated Products (216)Associated Documents - January 1, 2015•Document ID: 10147598Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
- Mfr Comm. #:
- 120815
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"SUBJECT N62TU: ISTA Service Function for DME ""RAM Backup"". The ISTA Service Function test plan should be performed to clear stored values in the DME RAM memory after repairs are completed, in the following situations: z VANOS or engine-related repairs if any of the following faults cannot be cleared: 2A90 - Exhaust camshaft, tooth offset to crankshaft 2A91 - Exhaust camshaft 2, tooth offset to crankshaft 2A8A - Inlet VANOS, adaptation stop 2A8B - Inlet VANOS, adaptation stop 2 2A8C - Exhaust VANOS, adaptation stop 2A8D - Exhaust VANOS, adaptation stop 2 2A8E - Inlet camshaft, tooth offset to crankshaft 2A8F - Inlet camshaft 2, tooth offset to crankshaft z The engine oil level display continues to show as overfilled even after being corrected. This is also described in SI B12 05 07."
Associated Products (70)Associated Documents - December 1, 2014•Document ID: 10148194Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840412
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
Associated Products (204)Associated Documents - December 1, 2014•Document ID: 10148166Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 122609
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN62TU: EDK Throttle Potentiometer Faults - Diagnostic. The "Service Engine Soon" and DSC/DTC warning lights are illuminated. Engine enters the power reduction ("fail-safe") mode. The following intermittent and "currently not present" EDK related faults may be stored in DME fault memory: ? 2CF8 - Throttle valve potentiometer, signal; and /or? 2CF9 - Throttle valve potentiometer 1, signal; and/or ? 2CFA - Throttle valve potentiometer 2; signal. In most cases DSC fault 5F77 (DME invalid data) may also be stored in DSC control module. These faults are sporadic and usually not reproducible. Resistance fluctuation in the EDK harness connector is causing an interruption of the EDK signal.
Associated Products (34)Associated Documents - November 1, 2014•Document ID: 10148423Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (138)Associated Documents - October 1, 2014•Document ID: 10149382Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 8403014
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Associated Products (215)Associated Documents - October 1, 2014•Document ID: 10149279Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 070314
- Date Added:
- November 26, 2018
- Manufacturer:
- BMW
SummaryDiagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Associated Products (142)Associated Documents - September 1, 2014•Document ID: 10148034Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 611714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor, function c. 2E8D - Intelligent battery sensor, signal transmission d. 2E8E - Intelligent battery sensor, communication CAUSE A faulty battery or IBS sensor (not both) The power management system and IBS in the vehicle cannot determine if the battery needs to be replaced. This is normal operation for all E-Series vehicles because they do not have the Advanced IBS sensor that the F-Series vehicles do. An external battery tester (Midtronics EXP-1000) must be used to determine if the battery needs to be replaced. Energy Diagnosis will not prompt for a battery replacement unless the battery is ""aged."" When energy diagnosis identifies the battery as ""aged,"" it means the amount of energy discharge over the course of the life of the battery has reached its maximum (worn out). In most cases, energy diagnosis states that the battery is OK. This is typically an indication of the current State of Charge (SoC), not the State of Health (SoH). The SoC is defined as the current amount of energy left in the battery (displayed as a percentage). The SoH is defined as an evaluation of the condition of the battery over a period of time (displayed as a percentage). For more information about batteries, refer to Training Manual ST051, ""07 Battery Basics."""
Associated Products (118)Associated Documents - September 1, 2014•Document ID: 10148018Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT; AIR BAGS
- Mfr Comm. #:
- 010914
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho
Associated Products (66)Associated Documents - August 1, 2014•Document ID: 10148376Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.
- Mfr Comm. #:
- 650511
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryPreviously assigned radio channels to the satellite radio "Presets" list have been erased and radio channels selected from the list "All channels" menu cannot be stored in the "Presets" list. The problem occurred after the recently implemented Sirius/XM channel lineup change. The data handling between the satellite radio receiver (SDARS-Exbox) and the Car Communication Computer (CCC head unit) has been corrupted.
Associated Products (73)Associated Documents - July 1, 2014•Document ID: 10148135Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- 840214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Associated Products (217)Associated Documents - July 1, 2014•Document ID: 10148120Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Associated Products (248)Associated Documents - June 1, 2014•Document ID: 10148101Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 840314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryiPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Associated Products (215)Associated Documents - April 1, 2014•Document ID: 10148276Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- 650514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryTraffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
Associated Products (209)Associated Documents - April 1, 2014•Document ID: 10148273Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 610314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Associated Products (242)Associated Documents - March 1, 2014•Document ID: 10148010Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 840114
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Associated Products (211)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents