BMW 435i Service Bulletins (2016)
325 manufacturer communications on file.
- December 1, 2015•Document ID: 10147873Service Bulletin/Repair InstructionsVISIBILITY:REARVIEW MIRRORS/DEVICES; VISIBILITY
- Mfr Comm. #:
- B512415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?SI B51 24 15December 2015 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B51 24 15 dated September 2015. designates changes to this revision SUBJECT Groaning Noise from the Exterior Mirror. A groaning noise is heard coming from the area around the outside mirror when opening and closing the door. The noise is more noticeable when the door is fully open to the end stop. CAUSE The outer front door weather strip rubs against the mirror housing.
Associated Products (16)Associated Documents - December 1, 2015•Document ID: 10147872Service Bulletin/Repair InstructionsSERVICE BRAKES, HYDRAULIC
- Mfr Comm. #:
- B340814
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?SI B34 08 14 Brakes December 2015 Technical Service This Service Information bulletin supersedes SI 34 08 14 dated July 2015. designates changes to this revision SUBJECT Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
Associated Products (34)Associated Documents - December 1, 2015•Document ID: 10147863Service Bulletin/Repair InstructionsENGINE; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B123314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (42)Associated Documents - December 1, 2015•Document ID: 10147860Service Bulletin/Repair InstructionsPOWER TRAIN; ENGINE
- Mfr Comm. #:
- B112615
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelivery Stop: B58 Engine - Check Crankshaft Bearing Shells.A Delivery Stop has been issued on F30 and F32 certain vehicles produced from July 2015 (start of production) to December 2, 2015. These vehicles may have upper guide bearing shells that may exhibit wear at low mileage. There are 45 vehicles affected by this stop. For your convenience, attached you will find the list of affected VINs. This bulletin will be updated with repair instructions and warranty information when it becomes available. Affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with a specific description.
Associated Products (28)Associated Documents - November 1, 2015•Document ID: 10147834Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B652015
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from speaker grills/ surrounds. There may be interference noises (rattles, squeaks, clicking) from the front or rear speaker grill/surrounds when the audio is on. CAUSE ? Contact between front door panel or speaker grill/surround with the speaker cone. ? Contact between the front door panel armrest support and trim for the folding compartment. ? Contact between the rear speaker grill/surround with the speaker cone.
Associated Products (8)Associated Documents - November 1, 2015•Document ID: 10147833Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B650915
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
Associated Products (132)Associated Documents - November 1, 2015•Document ID: 10147832Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- B640613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryA/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
Associated Products (32)Associated Documents - October 1, 2015•Document ID: 10147786Service Bulletin/Repair InstructionsEQUIPMENT; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B840415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"The illumination (back lighting) for the E-Call (Emergency/SOS call) button in the FZD (sunroof module) overhead console does not work. This picture shows the E-Call button illumination (back lighting) not working. Note: Pressing the E-Call button will start an SOS call, even though the back lighting is not working.This picture shows E-Call illumination (back lighting) working. AFFECTED VEHICLES This Service Action involves the F34 (3 Series Gran Turismo) and F36 (4 Series Gran Coupe) models, produced from 7/27/2015 to 7/30/2015. Please perform it the next time this vehicle comes to your workshop. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Missing wiring harness for the illumination of the E-Call button."
Associated Products (8)Associated Documents - October 1, 2015•Document ID: 10147785Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B660615
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySporadic Check Control Messages of the Driver Assistance System. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. This is due to the vehicle interior reaching very high temperatures. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) The following fault code is stored in the KAFAS control unit: 0x800AC0 - Switching off due to excess temperature Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again. Incorrect calibration of the temperature sensor in the KAFAS camera.
Associated Products (7)Associated Documents - October 1, 2015•Document ID: 10147771Service Bulletin/Repair InstructionsTIRES:PRESSURE MONITORING AND REGULATING SYSTEMS
- Mfr Comm. #:
- B360115
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryCheck Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Associated Products (43)Associated Documents - October 1, 2015•Document ID: 10147769Service Bulletin/Repair InstructionsPOWER TRAIN:AXLE ASSEMBLY
- Mfr Comm. #:
- B330215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
Associated Products (34)Associated Documents - September 1, 2015•Document ID: 10147272Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL
- Mfr Comm. #:
- B840515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryConnectedDrive Messages Are Not Received In the Vehicle. One or both of the following may occur: SMS based messages are not received in the vehicle. These are: Text messages - Office feature MyInfo Google send to car - addresses and Points of Interests (POI) Concierge The activation code is not accepted by the ConnectedDrive Portal. Software error in the HU-H (Head unit High).
Associated Products (28)Associated Documents - September 1, 2015•Document ID: 10147271Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B840315
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"HU-B: Bluetooth Connection Fails Sporadically. The Bluetooth system works intermittently. One or more of the following scenarios may occur: Bluetooth pairing is not possible - display shows ""Please wait"" Unable to select the check box to activate Bluetooth Device does not reconnect to the vehicle after a key cycle Audio interference noise is heard listening to iPod etc. When trying to access the user manual, the display shows ""Please wait"" Incorrect software installed in the HU-B (Headunit Basic)."
Associated Products (33)Associated Documents - September 1, 2015•Document ID: 10147269Service Bulletin/Repair InstructionsBACK OVER PREVENTION: AUTOMATIC SYSTEM BRAKING; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
- Mfr Comm. #:
- B660615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySporadic Check Control Messages of the Driver Assistance System. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. This is due to the vehicle interior reaching very high temperatures. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) The following fault code is stored in the KAFAS control unit: 0x800AC0 - Switching off due to excess temperature Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again. Incorrect calibration of the temperature sensor in the KAFAS camera.
Associated Products (6)Associated Documents - September 1, 2015•Document ID: 10147268Service Bulletin/Repair InstructionsLANE DEPARTURE: LANE KEEP: STEERING ASSIST
- Mfr Comm. #:
- B660515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryParking Maneuvering Assistant and Park Distance Control Failure. After activating the PMA (Parking Maneuvering Assistant) or PDC (Park Distance Control), the system stops functioning and a CCM (Check Control Message) is displayed advising the driver of the failure. The following fault code is stored in the PMA control unit 0x481E4D - PMA control unit internal, internal ASIC fault Software error in the PMA control unit Affected I-Level: F2x from F020-15-03-500 F3x from F020-15-07-500
Associated Products (19)Associated Documents - September 1, 2015•Document ID: 10147266Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES
- Mfr Comm. #:
- B651315
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryDWA - False Alarm. The alarm system sporadically activates by itself or the vehicle horn will be activated after the siren comes on. CAUSE Application error in DWA (Alarm System).
Associated Products (12)Associated Documents - September 1, 2015•Document ID: 10147264Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640715
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryIHKA - Outlet Temperature is Different on Both Sides. The IHKA settings on the left- and right-hand side are identical. The outlet temperature for both sides is different. Software application error in IHKA.
Associated Products (32)Associated Documents - September 1, 2015•Document ID: 10147263Service Bulletin/Repair InstructionsEQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"IHKA - Blower Runs in Emergency Mode. After the ignition is turned off and the vehicle is locked, the heating and air conditioning blower motor runs continuously. The next time the vehicle is started there may be the CCM (Check control message) displayed for ""Increased battery discharge"". CAUSE The blower output stage receives an invalid LIN bus signal during operation and switches to emergency mode. The blower will continue to run with the specified emergency mode after the ignition is turned off and the vehicle is locked."
Associated Products (34)Associated Documents - September 1, 2015•Document ID: 10147262Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER
- Mfr Comm. #:
- B640515
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryIHKA - Recirculation Function Changes from Manual to Automatic. While driving, the air recirculation button on IHKA changes by itself from manual to automatic or automatic to manual mode. CAUSE The IHKA operating software is too sensitive.
Associated Products (34)Associated Documents - September 1, 2015•Document ID: 10147250Service Bulletin/Repair InstructionsSTRUCTURE; VISIBILITY:REARVIEW MIRRORS/DEVICES; VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR
- Mfr Comm. #:
- B512415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryGroaning Noise from the Exterior Mirror. A groaning noise is heard coming from the area around the outside mirror when opening and closing the door. The noise is more noticeable when the door is fully open to the end stop. CAUSE The outer front door weather strip rubs against the mirror housing.
Associated Products (16)Associated Documents