BMW 428i Service Bulletins (2014)
422 manufacturer communications on file.
- May 1, 2015•Document ID: 10147136Service Bulletin/Repair InstructionsTIRES:VALVE; WHEELS
- Mfr Comm. #:
- B360215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryValve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
Associated Products (219)Associated Documents - May 1, 2015•Document ID: 10147134Service Bulletin/Repair InstructionsPOWER TRAIN; ELECTRICAL SYSTEM
- Mfr Comm. #:
- B270215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryRattling Noise from Transmission Tunnel. A rattling or knocking noise is heard in the area of the gear selector switch (GWS) during engine load reversal. CAUSE The vent tube for the transfer case is making contact with the transmission tunnel.
Associated Products (13)Associated Documents - May 1, 2015•Document ID: 10147130Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (74)Associated Documents - April 1, 2015•Document ID: 10152320Service Bulletin/Repair InstructionsSEAT BELTS
- Mfr Comm. #:
- B720115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryFront Safety Belt Slips Off Belt Extender. The customer states that the safety-belt extender on the front driver and/or passenger side fails to deliver the belt. One of the following situations may occur: 1. The belt extender fails to extend. 2. The belt extender extends, but the safety belt slips off the hand. CAUSE This may be caused by one or more of the following: ? The belt extender has mechanically and/or electrically failed. ? Excessive resistance from the safety-belt reel (twisted safety belt) does not allow the belt to extend properly, causing a failure to deliver the safety belt. ? The safety belt slips off the hand due to the geometry of the safety-belt extender, which fails to catch the safety belt for delivery.
Associated Products (4)Associated Documents - April 1, 2015•Document ID: 10152318Service Bulletin/Repair InstructionsUNKNOWN OR OTHER
- Mfr Comm. #:
- B660315
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummarySmart Opener Function Causes False Trunk Lid Activation. Sporadically the trunk lid will open (false activation) without a customer request. This occurs by just walking toward the rear of the vehicle with the remote. Smart opener software error
Associated Products (6)Associated Documents - April 1, 2015•Document ID: 10152317Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- B660115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummarySurround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
Associated Products (130)Associated Documents - April 1, 2015•Document ID: 10152306Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130315
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
Summary"N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"
Associated Products (79)Associated Documents - April 1, 2015•Document ID: 10152305Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B122114
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryEngine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (76)Associated Documents - April 1, 2015•Document ID: 10152302Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B120115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: ? 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
Associated Products (19)Associated Documents - March 1, 2015•Document ID: 10147690Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- B840514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryOne or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
Associated Products (150)Associated Documents - March 1, 2015•Document ID: 10147689Service Bulletin/Repair InstructionsVEHICLE SPEED CONTROL:CRUISE CONTROL
- Mfr Comm. #:
- B660215
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Remote Control Not Detected and/or Engine Will Not Start. One or more of the following situations can occur: 1. The remote control is not detected and the check control message (CCM) ""No remote control. Unable to start"" or ""Hold the remote control on the steering column"" is displayed. ? Fault code ""D90D1E - LIN bus error FBD receiver 1"" is stored. 2. The engine does not start with the CCM with ""Battery in the key is dead."" However, it must work when used with the second key. ? Fault Code ""9308B0 - ID transmitter: Battery undervoltage"" is stored. 3. The remote control is not detected and the CCM ""Central locking does not open,"" and/or ""Engine fails to start"" is displayed. An outside influence is causing interference with the remote control or the battery in the remote control key is defective."
Associated Products (34)Associated Documents - March 1, 2015•Document ID: 10147682Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN; VISIBILITY:REAR WINDOW WIPER/WASHER
- Mfr Comm. #:
- B610415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHorn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
Associated Products (32)Associated Documents - March 1, 2015•Document ID: 10147681Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B610315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryGeneral Electrical Systems Technical Service. Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: ? 627 - Steering behavior: Drive moderately ? 070 - Steering: Drive moderately ? 765 - Rear-end collision restricted ? 850 - Pedestrian warning restricted ? 236 - Driving stabilization: Drive moderately ? 299 - SOS call system failure ? 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ? ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter ? FEM - D91DE0 No message, receiver FEM, transmitter TMSL ? FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ? ACSM - C9540C Message missing, receiver ACSM, transmitter FEM ? TMSL - D95402 Message missing, receiver TMSL, transmitter FEM ? KOMBI - E11454 No message, receiver KOMBI, transmitter REM ? FEM - D91DE6 No message, receiver FEM, transmitter TMSL ? TMSR - D99401 Message missing, receiver TMSR, transmitter FEM ? TMSR - D99402 Message missing, receiver TMSR, transmitter FEM ? FEM - 8041BA AHL system faulty ? FEM - D916C3 No message, receiver FEM, transmitter TCB ? ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM ? TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM ? TMSL- D95401 Message missing, receiver TMSR, transmitter FEM ? HU-H - S0397 MOST configuration was not stored ? TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault ? FEM - 8041B6 LWR faulty ? REM - E58468 Body CAN2; communication fault ? TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM ? FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted KCAN wiring under driver or passenger seat.
Associated Products (20)Associated Documents - March 1, 2015•Document ID: 10147676Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT
- Mfr Comm. #:
- B510315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Front Floor Mats Do Not Stay in Place. The Velcro patch attached to the bottom of the floor mat peels off. Poor adhesion of the Velcro patch Thank you for all the PuMA ""Info Only"" cases. From these cases, it has been determined that the Velcro peeling fault occurs on mats produced prior to May 2014. We no longer need ""Info Only"" cases from this time period."
Associated Products (28)Associated Documents - March 1, 2015•Document ID: 10147667Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ENGINE
- Mfr Comm. #:
- B123314
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Associated Products (42)Associated Documents - March 1, 2015•Document ID: 10147652Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110315
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryN20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
Associated Products (79)Associated Documents - February 1, 2015•Document ID: 10147091Service Bulletin/Repair InstructionsAIR BAGS
- Mfr Comm. #:
- 650414
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
Associated Products (117)Associated Documents - February 1, 2015•Document ID: 10147084Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; POWER TRAIN
- Mfr Comm. #:
- 610314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
Associated Products (115)Associated Documents - February 1, 2015•Document ID: 10147073Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 122114
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummarySI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
Associated Products (70)Associated Documents - February 1, 2015•Document ID: 10057707Service Bulletin/Repair InstructionsAIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE; INTERIOR LIGHTING
- Mfr Comm. #:
- SI B65 04 14
- Date Added:
- June 22, 2015
- Manufacturer:
- BMW
SummaryBMW:SOME BMW MODELS MAY OR MAY NOT DISPLAY AIRBAG WARNING LIGHT. *TA
Associated Products (39)Associated Documents