BMW 335i Service Bulletins (2012)
556 manufacturer communications on file.
- February 1, 2014•Document ID: 10147974Service Bulletin/Repair InstructionsVISIBILITY:SUN/MOON ROOF ASSEMBLY
- Mfr Comm. #:
- 540213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?Sunroof Gets Stuck or Moves in Small Steps. During opening or closing the sunroof, one or more of the following situations may occur: 1. The sunroof becomes stuck 2. One-touch open and close no longer works 3. The sunroof moves in small steps. CAUSE Software error in the sunroof control module (FZD) Some or all of the following fault codes may be stored: 0x030212 - SHD: Activation timeout, no block recognition 0x030214 - SHD: Zero position passed, loss of calibration 0x030215 - SHD: Invalid characteristic curve, not normalized 0x030216 - SHD: 90% motor temperature threshold exceeded 0x030217 - SHD: Motor operation interrupted by overheating 0x030218 - SHD: Motor does not start due to overvoltage or undervoltage 0x030219 - SHD: Errors in the checksum coding 0x03021C - SHD: Not initialized due to invalid marginal conditions (motor driver) 0x030220 - SHD: System not normalized 0x801A02 - Coding: Control unit is not coded.
Associated Products (13)Associated Documents - February 1, 2014•Document ID: 10147973Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; VISIBILITY
- Mfr Comm. #:
- 510714
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryNoise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147972Service Bulletin/Repair InstructionsEQUIPMENT; STRUCTURE
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog.
Associated Products (20)Associated Documents - February 1, 2014•Document ID: 10147967Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; ENGINE
- Mfr Comm. #:
- 122513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryReduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation.
Associated Products (12)Associated Documents - January 1, 2014•Document ID: 10147954Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- 653009
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryEnabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Associated Products (119)Associated Documents - January 1, 2014•Document ID: 10147953Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
Associated Products (208)Associated Documents - January 1, 2014•Document ID: 10147952Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 652413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryHeadunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.
Associated Products (90)Associated Documents - January 1, 2014•Document ID: 10147950Service Bulletin/Repair InstructionsVISIBILITY; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING
- Mfr Comm. #:
- 640713
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147949Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING; VISIBILITY
- Mfr Comm. #:
- 640613
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?SI B64 06 13 January 2014 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B64 06 13 dated November 2013. designates changes to this revision SUBJECT A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Associated Products (13)Associated Documents - January 1, 2014•Document ID: 10147945Service Bulletin/Repair InstructionsEXTERIOR LIGHTING
- Mfr Comm. #:
- 630414
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryDelay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
Associated Products (230)Associated Documents - January 1, 2014•Document ID: 10147943Service Bulletin/Repair InstructionsEXTERIOR LIGHTING; EXTERIOR LIGHTING:FOG LIGHTS; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 630214
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryFog Light Operation Changed After Programming. After the vehicle is programmed with ISTA/P 2.49.x or 2.50.x (integration level earlier than F02013-11-502), the fog lights cannot be operated when the light switch is in the parking light position. Note: The fog light operation has been changed in vehicles produced from March 2013. The fog lights cannot be operated when the light switch is in the park position. This is normal operation due to state legislative requirements that have changed; no further action is required. CAUSE Software error with ISTA/P 2.49.x and 2.50.x
Associated Products (13)Associated Documents - January 1, 2014•Document ID: 10147941Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 612906
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryELV Does Not Release. Cause 1: The steering column is held against the steering lock because of torque from the steering gear. In such cases, a yellow check control warning (CC ID# 187) is shown in the instrument cluster, but no faults are stored. Cause 2: Communication fault in the CAS (Car Access System) and ELV system network and/or battery low. The problem may cause the ELV warning to be displayed in yellow or red.
Associated Products (81)Associated Documents - January 1, 2014•Document ID: 10147937Service Bulletin/Repair InstructionsSTRUCTURE:BODY:TRUNK LID
- Mfr Comm. #:
- 510807
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryErroneous Trunk Lid Open Check Control Message. The trunk open check control message may appear, even though the trunk lid or tailgate is fully closed and latched. CAUSE Incorrect adjustment of the trunk latch striker
Associated Products (37)Associated Documents - January 1, 2014•Document ID: 10147936Service Bulletin/Repair InstructionsEQUIPMENT
- Mfr Comm. #:
- 510514
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Remove Water Drain Plugs from E-Box. The water drain plugs for the left- and right-side E-box may clog. This can lead to water collection/corrosion and allow water to enter the passenger compartment. CAUSE The water drain plug slots are too small.
Associated Products (20)Associated Documents - January 1, 2014•Document ID: 10147933Service Bulletin/Repair InstructionsSERVICE BRAKES
- Mfr Comm. #:
- 340913
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryBrake Squeal. Squeaking noises from the front or rear axle when braking. The squeaking noise when braking may have different causes, depending on the axle.
Associated Products (4)Associated Documents - January 1, 2014•Document ID: 10147932Service Bulletin/Repair InstructionsSTEERING
- Mfr Comm. #:
- 320413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummarySqueaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle gaiter is insufficiently lubricated.
Associated Products (6)Associated Documents - January 1, 2014•Document ID: 10147930Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 240413
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryGM6 - 6L45R: Diagnostic Procedure for Shudder or Vibration Issues. A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.
Associated Products (58)Associated Documents - January 1, 2014•Document ID: 10147929Service Bulletin/Repair InstructionsENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE
- Mfr Comm. #:
- 180213
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"Exhaust Flap Actuator Is Loose. INFORMATION Covered under the terms of the BMW New Vehicle/SAV Limited Warranty Defect Code:18 12 03 39 00https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Labor Operation:Labor Allowance:Refer to KSDReplacing exhaust flap actuator driveLabor operation code 18 12 081 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 18 12 581 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field."
Associated Products (16)Associated Documents - January 1, 2014•Document ID: 10147706Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- 121513
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
Associated Products (54)Associated Documents - November 1, 2013•Document ID: 10150193Service Bulletin/Repair InstructionsTIRES
- Mfr Comm. #:
- BMWNOV0613
- Date Added:
- December 3, 2018
- Manufacturer:
- BMW
SummaryService Information bulletin B36 03 13 has been published for the Delivery Stop issued on Wednesday, November 13. The Delivery Stop affects certain 2014 model year F30, F31 and F32 October 2013 production vehicles. Tire Identification numbers (molding number and DOT number) must be checked and if necessary, affected tires replaced. Affected vehicles in center inventory must not be delivered until the tires have been checked. The small number of affected vehicles can be identified via the Key Reader, DCS Inquiry or ISPA with the description: Defect Code 0036820100, Delivery Stop, B36 03 13 Check Tire ID
Associated Products (13)Associated Documents