Mercedes-Benz CLA-Class Service Bulletins (2019)

158 manufacturer communications on file.

• September 16, 2024•Document ID: 11008056

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI07.70-P-078078

  Date Added:

  September 26, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.

  Associated Products (40)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz A-Class+ 20 more
  Associated Documents

  • DownloadMC-11008056-0001.pdf↗
• September 10, 2024•Document ID: 11008323

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078302

  Date Added:

  October 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.

  Associated Products (119)

  2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz A-Class+ 99 more
  Associated Documents

  • DownloadMC-11008323-0001.pdf↗
• September 10, 2024•Document ID: 11007753

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  September 13, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11007753-0001.pdf↗
• September 9, 2024•Document ID: 11007790

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078304

  Date Added:

  September 14, 2024

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.

  Associated Products (109)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz S-Class+ 89 more
  Associated Documents

  • DownloadMC-11007790-0001.pdf↗
• July 23, 2024•Document ID: 11005294

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078069

  Date Added:

  July 27, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11005294-0001.pdf↗
• July 17, 2024•Document ID: 11005313

  Service Bulletin/Repair Instructions
  ENGINE

  Mfr Comm. #:

  LI07.70-P-078047

  Date Added:

  July 30, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.

  Associated Products (40)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2021 Mercedes-Benz A-Class+ 20 more
  Associated Documents

  • DownloadMC-11005313-0001.pdf↗
• April 30, 2024•Document ID: 10253708

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  CL - 240401

  Date Added:

  May 1, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.

  Associated Products (17)

  2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2020 Mercedes-Benz A-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz GLA-Class2020 Mercedes-Benz GLB-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class2019 Mercedes-Benz A-Class2019 Mercedes-Benz CLA-Class2019 Mercedes-Benz GLA-Class2019 Mercedes-Benz GLE-Class2019 Mercedes-Benz GLS-Class
  Associated Documents

  • DownloadMC-10253708-0001.pdf↗
• April 26, 2024•Document ID: 10253703

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA - 20240402

  Date Added:

  May 1, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

  Associated Products (56)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT+ 36 more
  Associated Documents

  • DownloadMC-10253703-0001.pdf↗
• April 23, 2024•Document ID: 10253772

  Service Bulletin/Repair Instructions
  ENGINE AND ENGINE COOLING

  Mfr Comm. #:

  LI20.10-P-076206

  Date Added:

  May 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Customer states that the CEL is lit in the instrument cluster Debris in the coolant system Please refer to the specific repair instructions for the vehicle you are working on in the attachments section of this LI. Before beginning work on the vehicle open a TIPS case and request the tool you will need. In your request include a contact name, phone number, and shipping address for the tool to be sent. Before the tool arrives: Remove and replace the coolant expansion tank (reservoir) and the main radiator. Without removing the components: flush the heater core and changeover valve (located in the right front wheel arch) in the opposite direction of flow until no debris remains. Once the tool arrives, proceed with flushing the vehicle per the instructions attached in this LI. A picture of the filter after each flush must be taken. If after the prescribed number of flushing attempts debris is still being collected in the filter, upload all the pictures to the TIPS case and wait for next steps.

  Associated Products (15)

  2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2020 Mercedes-Benz CLA-Class2019 Mercedes-Benz CLA-Class
  Associated Documents

  • DownloadMC-10253772-0001.pdf↗
• January 29, 2024•Document ID: 10249540

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU-OTA Comm Mod

  Date Added:

  February 2, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.

  Associated Products (45)

  2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz E-Class+ 25 more
  Associated Documents

  • DownloadMC-10249540-0001.pdf↗
• January 24, 2024•Document ID: 10249495

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-077314

  Date Added:

  February 1, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!

  Associated Products (88)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class+ 68 more
  Associated Documents

  • DownloadMC-10249495-0001.pdf↗
• January 24, 2024•Document ID: 10249482

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-077313

  Date Added:

  February 1, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgeräusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.

  Associated Products (86)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class+ 66 more
  Associated Documents

  • DownloadMC-10249482-0001.pdf↗
• January 18, 2024•Document ID: 10249726

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  NCU-OTAcommNoMMC

  Date Added:

  February 6, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.

  Associated Products (53)

  2021 Mercedes-Benz AMG GT2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLC-Class2021 Mercedes-Benz GLE-Class2021 Mercedes-Benz GLS-Class2021 Mercedes-Benz S-Class2020 Mercedes-Benz AMG GT2020 Mercedes-Benz C-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz CLS-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz GLC-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz GLS-Class2020 Mercedes-Benz S-Class2020 Mercedes-Benz SLC-Class2020 Mercedes-Benz SL-Class+ 33 more
  Associated Documents

  • DownloadMC-10249726-0001.pdf↗
• December 7, 2023•Document ID: 10248195

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA-Comm Mod SW

  Date Added:

  January 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

  Associated Products (65)

  2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz EQB-Class+ 45 more
  Associated Documents

  • DownloadMC-10248195-0001.pdf↗
• December 4, 2023•Document ID: 10248162

  Service Bulletin/Repair Instructions
  SEATS

  Mfr Comm. #:

  LI91.18-P-077075

  Date Added:

  January 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Crease formation on genuine leather seat covers in vehicles with low mileage • Objects left on the seats for extended periods of time (pressure marks). • Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). • Light initial creases due to vehicle handling. • Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!

  Associated Products (241)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class+ 221 more
  Associated Documents

  • DownloadMC-10248162-0001.pdf↗
• December 1, 2023•Document ID: 10248203

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  OTA-Head Unit SW

  Date Added:

  January 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

  Associated Products (50)

  2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class+ 30 more
  Associated Documents

  • DownloadMC-10248203-0001.pdf↗
• November 17, 2023•Document ID: 10246281

  Service Bulletin/Repair Instructions
  ENGINE AND ENGINE COOLING

  Mfr Comm. #:

  LI07.70-P-070763

  Date Added:

  December 6, 2023

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.

  Associated Products (36)

  2023 Mercedes-Benz E-Class2022 Mercedes-Benz E-Class2021 Mercedes-Benz C-Class2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLC-Class2021 Mercedes-Benz GLE-Class2020 Mercedes-Benz C-Class2020 Mercedes-Benz E-Class2020 Mercedes-Benz GLC-Class2020 Mercedes-Benz SLC-Class2019 Mercedes-Benz C-Class2019 Mercedes-Benz CLA-Class2019 Mercedes-Benz E-Class2019 Mercedes-Benz GLA-Class2019 Mercedes-Benz GLC-Class2019 Mercedes-Benz SLC-Class2018 Mercedes-Benz C-Class2018 Mercedes-Benz CLA-Class2018 Mercedes-Benz E-Class2018 Mercedes-Benz GLA-Class+ 16 more
  Associated Documents

  • DownloadMC-10246281-0001.pdf↗
• October 10, 2023•Document ID: 10244837

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-076800

  Date Added:

  November 3, 2023

  Manufacturer:

  MERCEDES-BENZ

  Summary

  The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.

  Associated Products (84)

  2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2022 Mercedes-Benz GLC-Class2022 Mercedes-Benz GLE-Class2022 Mercedes-Benz GLS-Class2022 Mercedes-Benz S-Class2022 Mercedes-Benz SL-Class2021 Mercedes-Benz A-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz C-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz CLS-Class2021 Mercedes-Benz E-Class+ 64 more
  Associated Documents

  • DownloadMC-10244837-0001.pdf↗
• August 28, 2023•Document ID: 10241527

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE

  Mfr Comm. #:

  NCU-HU SW Update

  Date Added:

  September 1, 2023

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customer’s vehicle. The OTA may be validated as successful on the customer’s Mercedes Me connect app under “Over-the-Air Vehicle Updates” as “Update for the communication module”. If the OTA is successful it will show a green “installed” and date of installation in the Over-the-Air update section.

  Associated Products (82)

  2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz G-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz AMG GT2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz CLS-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz G-Class+ 62 more
  Associated Documents

  • DownloadMC-10241527-0001.pdf↗
• August 18, 2023•Document ID: 10241790

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; EQUIPMENT

  Mfr Comm. #:

  LI82.85-P-076799

  Date Added:

  September 5, 2023

  Manufacturer:

  MERCEDES-BENZ

  Summary

  The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.

  Associated Products (79)

  2023 Mercedes-Benz E-Class2022 Mercedes-Benz E-Class2022 Mercedes-Benz GLC-Class2021 Mercedes-Benz AMG GT2021 Mercedes-Benz E-Class2021 Mercedes-Benz GLC-Class2021 Mercedes-Benz S-Class2020 Mercedes-Benz AMG GT2020 Mercedes-Benz E-Class2020 Mercedes-Benz GLA-Class2020 Mercedes-Benz GLC-Class2020 Mercedes-Benz GLE-Class2020 Mercedes-Benz S-Class2020 Mercedes-Benz SL-Class2019 Mercedes-Benz AMG GT2019 Mercedes-Benz CLA-Class2019 Mercedes-Benz CLS-Class2019 Mercedes-Benz E-Class2019 Mercedes-Benz GLA-Class2019 Mercedes-Benz GLC-Class+ 59 more
  Associated Documents

  • DownloadMC-10241790-0001.pdf↗