Jeep Wagoneer Service Bulletins (2024)
459 manufacturer communications on file.
- August 20, 2024•Document ID: 11006630Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 9100401REV1
- Date Added:
- August 26, 2024
- Manufacturer:
- JEEP
Summary3.5" speaker assembly Before replacing a speaker part for crackles or rattling noises make sure to take the following steps: 1. Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. 4. Remove the bad speaker and replace it back. 5. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement. Follow all these steps, if issue still happens; reach out to the engineer at Stellantis for more support, if the engineer doesn t respond in 30 minutes. Then the speaker can be replaced.
Associated Products (4)Associated Documents - August 12, 2024•Document ID: 11006346Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 9100401
- Date Added:
- August 14, 2024
- Manufacturer:
- JEEP
Summary3.5" speaker assembly Before replacing a speaker part for crackles or rattling noises make sure to take the following steps: 1. Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement.
Associated Products (4)Associated Documents - August 9, 2024•Document ID: 11006221Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; SERVICE BRAKES; FORWARD COLLISION AVOIDANCE: WARNINGS
- Mfr Comm. #:
- S248A000013
- Date Added:
- August 12, 2024
- Manufacturer:
- JEEP
SummaryAfter Radio Software Update, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on in Cluster or Other Customer Programable Features Concerns Not Set, No Diagnostic Trouble Codes (DTCs)
Associated Products (12)Associated Documents - August 7, 2024•Document ID: 11006241Service Bulletin/Repair InstructionsSTRUCTURE:BODY; ELECTRICAL SYSTEM
- Mfr Comm. #:
- 23-004-24 REV. A
- Date Added:
- August 13, 2024
- Manufacturer:
- JEEP
Summary"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses."
Associated Products (37)2024 Dodge Durango2024 Jeep Compass2024 Jeep Gladiator2024 Jeep Grand Cherokee2024 Jeep Grand Wagoneer2024 Jeep Renegade2024 Jeep Wagoneer2024 Jeep Wrangler2024 Ram 15002023 Dodge Durango2023 Jeep Cherokee2023 Jeep Compass2023 Jeep Gladiator2023 Jeep Grand Cherokee2023 Jeep Grand Wagoneer2023 Jeep Renegade2023 Jeep Wagoneer2023 Jeep Wrangler2023 Ram 15002022 Dodge Durango+ 17 moreAssociated Documents - August 3, 2024•Document ID: 11006236Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- S2108000249 REV.C
- Date Added:
- August 12, 2024
- Manufacturer:
- JEEP
SummaryCluster and Radio Display Settings Revert Back to Default Settings, Auto Door Locks and Paddle Shifter Inoperative With No Menu to Enable, Pedestrian Emergency Brake (PEB) Lamp and Forward Collision Warning (FCW) Lamp on After a Recent Service Repair no Diagnostic Trouble Codes (DTCs)
Associated Products (13)Associated Documents - August 2, 2024•Document ID: 11006235Service Bulletin/Repair InstructionsSTRUCTURE:BODY
- Mfr Comm. #:
- S2423000030 REV.A
- Date Added:
- August 12, 2024
- Manufacturer:
- JEEP
SummaryBuzz Squeak Rattle (BSR) From Upper Left Dash Area.
Associated Products (6)Associated Documents - July 26, 2024•Document ID: 11005275Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STRUCTURE:BODY
- Mfr Comm. #:
- S2408000016 REV.A
- Date Added:
- July 26, 2024
- Manufacturer:
- JEEP
SummaryFront Passenger, Rear right and/or Rear left Window Door Window Switches are Inoperative, Window Operation Does Work from the Driver Master Switch
Associated Products (6)Associated Documents - July 25, 2024•Document ID: 11005321Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 18-063-24
- Date Added:
- July 30, 2024
- Manufacturer:
- JEEP
Summary"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06DD - Engine Oil Pressure Control Circuit Performance/Stuck Off. ● P00F3 - Humidity Sensor Circuit Range/Performance. Customer may also experience one or more of the following: ● Customers may experience coasting complaints at lower speed. ● Undesirable vehicle drivability behavior causing a vehicle Shift to Park event during Engine Stop Start (ESS) while Adaptive Cruise Control (ACC) is active. ● Pressing ACC button while ESS active can shift the vehicle to park. ● Idle speed oscillations observed when in Snow and Mud modes. ● Poor engine performance (undershoots engine speed) for ESS and for non-ESS engine start. ● Screen two incorrectly pops up on the Instrument Cluster Panel (IPC) for 5 seconds during Terrain and Rock mode. This bulletin involves reprogramming the PCM with the latest available software."
Associated Products (2)Associated Documents - July 24, 2024•Document ID: 11005356OtherPOWER TRAIN
- Mfr Comm. #:
- 99500
- Date Added:
- July 31, 2024
- Manufacturer:
- JEEP
SummaryCARRIER – PLANETARY & SHAFT KIT - OUTPUT
Associated Products (42)2025 Dodge Durango2025 Jeep Gladiator2025 Jeep Grand Cherokee2025 Jeep Grand Wagoneer2025 Jeep Wagoneer2025 Jeep Wrangler2025 Ram 15002024 Dodge Durango2024 Jeep Gladiator2024 Jeep Grand Cherokee2024 Jeep Grand Wagoneer2024 Jeep Wagoneer2024 Jeep Wrangler2024 Ram 15002023 Chrysler 3002023 Dodge Challenger2023 Dodge Charger2023 Dodge Durango2023 Jeep Gladiator2023 Jeep Grand Cherokee+ 22 moreAssociated Documents - July 24, 2024•Document ID: 11005207Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- S2408000080
- Date Added:
- July 24, 2024
- Manufacturer:
- JEEP
SummaryDifferent Cluster Displays Have a Reduced View While in Analog Mode, Darkened Sides
Associated Products (4)Associated Documents - July 19, 2024•Document ID: 11004978Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; STRUCTURE:BODY
- Mfr Comm. #:
- S2408000079
- Date Added:
- July 19, 2024
- Manufacturer:
- JEEP
SummaryLow Battery, No Crank No Start, Cluster Message “Service Keyless System”, Intermittent Power Liftgate Operation
Associated Products (9)Associated Documents - July 11, 2024•Document ID: 11004344Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 9100388
- Date Added:
- July 11, 2024
- Manufacturer:
- JEEP
SummaryBODY CONTROL MODULE After Battery Drainage BCM do not work. Please follow the following steps. 1. Check the BCM PROXI, if the BCM or any other modules are not aligned, then perform the PROXI alignment, reset the modules and perform normal ignition cycle (OFF to RUN to OFF) 2. If PROXI is correct (No misalignment), then reset the BCM module and perform normal ignition cycle. 3. Check for the DTC's and check wiring and components related to those DTC's and clear them
Associated Products (2)Associated Documents - July 11, 2024•Document ID: 11004342Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- 9100386
- Date Added:
- July 11, 2024
- Manufacturer:
- JEEP
SummarySecurity Gateway Module Battery Voltage - Circuit Voltage Below Threshold - DTC B2199-16 Repair Action : 1) Check OR Replacing cabling. 2) Check OR Replacing connector. 3) Check the battery is good OR Replacing battery. 4) Check OR Replacing FUSE. 5) Check SGW terminal. Battery Voltage - Circuit Voltage Above Threshold - DTC B2199-17 Repair Action : 1) Check OR Replacing cabling. 2) Check OR Replacing connector. 3) Check the battery is good OR Replacing battery. 4) Check OR Replacing FUSE. 5) Check SGW terminal. CAN Bus- [C-CAN1] (Node mute) or CAN Bus Off Performance- (Bus off failure) - Check DTC in DTC matrix Repair Action: 1) CAN Lines Check 2) Read Fault memory of all nodes 3) Check and download the right calibration file for current vehicle configuration Ethernet Bus Failure - Check DTC Repair Action: 1) CAN Lines Check 2) Read Fault memory of all nodes 3) Check and download the right calibration file for current vehicle configuration ECU-In-Plant-Mode - B235A-00 Repair Action: Install Calibration file with correct policy Ecu Internal Performance - Internal Electronic Failure - DTC B22A9-49 Repair Action: 1. If its in store clear and check again if DTC shows up. 2. Check battery voltage 3. Issue still exist then change ECU ECU Not Programmed / Flash Required (No Valid Application) - DTC C221C-00 Repair Action: 1. Reflash ECU with correct file Control Module Security Certificate Missing/Invalid - DTC U3033-00 or U3033-01 Repair Action: 1. Check connectivity 2. Ethernet network 3. Flash with the latest FOTA App Code 4. Flash the cert store with correct certificate 5. Clear Faults
Associated Products (7)Associated Documents - July 10, 2024•Document ID: 11004151Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- S2408000015 REV.C
- Date Added:
- July 10, 2024
- Manufacturer:
- DODGE
SummaryRemote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
Associated Products (40)2024 Jeep Compass2024 Jeep Gladiator2024 Jeep Grand Wagoneer2024 Jeep Wagoneer2024 Jeep Wrangler2024 Ram 15002024 Ram 25002024 Ram 35002024 Ram 45002024 Ram 55002023 Dodge Durango2023 Jeep Cherokee2023 Jeep Compass2023 Jeep Gladiator2023 Jeep Grand Wagoneer2023 Jeep Wagoneer2023 Jeep Wrangler2023 Ram 15002023 Ram 25002023 Ram 3500+ 20 moreAssociated Documents - July 2, 2024•Document ID: 11003281Service Bulletin/Repair InstructionsSEATS
- Mfr Comm. #:
- 9100364
- Date Added:
- July 4, 2024
- Manufacturer:
- JEEP
SummarySeat Control Module 3RD ROW SEAT WILL NOT CLOSE FULLY DOWN CUSTOMER STATES THE PASSENGER SIDE 3RD ROW WILL NOT CLOSE FULLY DOWN Steps for Tech: Before recalibrating 3rd row see please follow below mentioned steps first. -Turn off vehicle for 2 minute and then turn on vehicle and press 3rd row seat switch 2 times - Seat will start moving and relearn its correct hard stops and parameters. -Seat will recalibrate itself with updated SW.
Associated Products (6)Associated Documents - June 28, 2024•Document ID: 11002531Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- S2408000066
- Date Added:
- June 28, 2024
- Manufacturer:
- DODGE
SummaryDrained Battery, Low System Voltage, Battery Not Charging, High System Voltage
Associated Products (46)2025 Dodge Durango2025 Jeep Gladiator2025 Jeep Grand Cherokee2025 Jeep Grand Wagoneer2025 Jeep Wagoneer2025 Ram 15002024 Dodge Durango2024 Jeep Compass2024 Jeep Gladiator2024 Jeep Grand Cherokee2024 Jeep Grand Wagoneer2024 Jeep Wagoneer2024 Ram 15002024 Ram 25002024 Ram 35002024 Ram 45002024 Ram 55002023 Chrysler 3002023 Dodge Challenger2023 Dodge Charger+ 26 moreAssociated Documents - June 28, 2024•Document ID: 11002528Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- S2408000067
- Date Added:
- June 28, 2024
- Manufacturer:
- JEEP
SummaryThe Electronic Vehicle Information Center (EVIC) Displays Park Assist System Disabled Message
Associated Products (12)Associated Documents - June 25, 2024•Document ID: 11002828Service Bulletin/Repair InstructionsENGINE; ELECTRICAL SYSTEM
- Mfr Comm. #:
- S1408000384 REV.F
- Date Added:
- July 2, 2024
- Manufacturer:
- CHRYSLER
Summary"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
Associated Products (74)2025 Dodge Durango2025 Jeep Gladiator2025 Jeep Grand Cherokee2025 Jeep Grand Wagoneer2025 Jeep Wagoneer2024 Alfa Romeo Stelvio2024 Chrysler Pacifica2024 Chrysler Voyager2024 Dodge Durango2024 Dodge Hornet2024 Jeep Compass2024 Jeep Gladiator2024 Jeep Grand Cherokee2024 Jeep Grand Wagoneer2024 Jeep Wagoneer2024 Jeep Wrangler2024 Ram 15002024 Ram 35002024 Ram 45002024 Ram 5500+ 54 moreAssociated Documents - June 18, 2024•Document ID: 11002024Service Bulletin/Repair InstructionsELECTRICAL SYSTEM; EXTERIOR LIGHTING
- Mfr Comm. #:
- S2308000120 REV.B
- Date Added:
- June 24, 2024
- Manufacturer:
- RAM
SummaryRain Sensing Auto Wipers and Auto on Head Lamps Inoperative
Associated Products (33)2025 Jeep Compass2025 Jeep Grand Cherokee2025 Jeep Grand Wagoneer2025 Jeep Wagoneer2025 Jeep Wagoneer S2025 Ram 15002024 Jeep Compass2024 Jeep Grand Cherokee2024 Jeep Grand Wagoneer2024 Jeep Wagoneer2024 Ram 15002024 Ram 25002024 Ram 35002024 Ram 45002024 Ram 55002023 Jeep Compass2023 Jeep Grand Cherokee2023 Jeep Grand Wagoneer2023 Jeep Wagoneer2023 Ram 1500+ 13 moreAssociated Documents - June 15, 2024•Document ID: 11001825Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- 18-056-24
- Date Added:
- June 18, 2024
- Manufacturer:
- JEEP
Summary"Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. ● P0300-00 - Multiple Cylinder Misfire. Customers may also comment on one or more of the following: ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezing temperatures. This bulletin involves reprogramming the PCM with the latest available software."
Associated Products (2)Associated Documents