BMW ActiveHybrid 7 Service Bulletins (2012)
280 manufacturer communications on file.
- August 1, 2015•Document ID: 10151411Service Bulletin/Repair InstructionsSUSPENSION:FRONT:MACPHERSON STRUT; SUSPENSION
- Mfr Comm. #:
- B370215
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"The ""Variable Damper Control"" (VDC) valves for the spring strut shock absorber on the left front axle may fail, causing the Check Control message: ""Chassis function restricted. It is possible to continue driving. Have the system checked as soon as possible by your local BMW Service Workshop"" to be displayed."
Associated Products (40)Associated Documents - August 1, 2015•Document ID: 10151404Service Bulletin/Repair InstructionsPOWER TRAIN
- Mfr Comm. #:
- B270315
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
SummaryVibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
Associated Products (142)Associated Documents - August 1, 2015•Document ID: 10151400Service Bulletin/Repair InstructionsEQUIPMENT; ENGINE
- Mfr Comm. #:
- B111715
- Date Added:
- December 10, 2018
- Manufacturer:
- BMW
Summary"N63 and S63 Engine: Upper Oil Pan Removal and Installation Procedures. INFORMATION When removing and/or installing the N63 or S63 engine ""upper"" oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the upper oil pan bolts as per Repair Instruction 11 13 010 ""Removing and installing /replacing upper oil sump (N63),"" the steps outlined in the attachment of this bulletin must be followed. Refer to attached document and the instruction section that applies to the procedure being carried out. The ISTA/D repair instructions are currently being revised."
Associated Products (58)Associated Documents - July 1, 2015•Document ID: 10147211Service Bulletin/Repair InstructionsEQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT
- Mfr Comm. #:
- B651015
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryNAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
Associated Products (132)Associated Documents - July 1, 2015•Document ID: 10147202Service Bulletin/Repair InstructionsEQUIPMENT:OTHER:LABELS
- Mfr Comm. #:
- B511615
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
Associated Products (143)Associated Documents - July 1, 2015•Document ID: 10147198Service Bulletin/Repair InstructionsSTRUCTURE; POWER TRAIN
- Mfr Comm. #:
- B330115
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCracking in Rear Differential Mount Bushing. During inspection, the rear differential mount in the rear axle support shows signs of cracking.
Associated Products (60)Associated Documents - July 1, 2015•Document ID: 10147192Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
- Mfr Comm. #:
- B130215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."
Associated Products (96)Associated Documents - July 1, 2015•Document ID: 10147188Service Bulletin/Repair InstructionsEQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE
- Mfr Comm. #:
- B121015
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion (8KL) performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly for the above models with previous versions of ISTA/P. After the conversion, the forecast interval did not change to the desired 10,000 miles/12 months, or the forecast is displayed as an invalid value, for example: 25,000 miles/24 months. 1. Incorrect DME coding or calibration data 2. The ISTA CBS correction test plan contains an error when attempting to correct an invalid oil service prognosis value.
Associated Products (12)Associated Documents - June 1, 2015•Document ID: 10147723Service Bulletin/Repair InstructionsELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE
- Mfr Comm. #:
- B620415
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryService Action: Programming Control Units. Sporadically the vehicle cannot be started, due to a discharged battery caused by a software glitch in the instrument cluster.
Associated Products (50)Associated Documents - June 1, 2015•Document ID: 10147722Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:12V/24V/48V BATTERY
- Mfr Comm. #:
- B613014
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
Summary"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
Associated Products (89)Associated Documents - June 1, 2015•Document ID: 10147715Service Bulletin/Repair InstructionsSUSPENSION
- Mfr Comm. #:
- B310112
- Date Added:
- November 13, 2018
- Manufacturer:
- BMW
SummaryClicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Associated Products (79)Associated Documents - May 1, 2015•Document ID: 10147155Service Bulletin/Repair InstructionsELECTRICAL SYSTEM:WIRING: REAR COMPARTMENT/TRUNK; STRUCTURE:BODY:TRUNK LID; LATCHES/LOCKS/LINKAGES:TRUNK LID:LOCK
- Mfr Comm. #:
- B660415
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryTrunk Lid Does Not Operate with Remote After Programming. If the customer profile is assigned to only unlock the driver door after programming with ISTA/P 3.55.x, the trunk will not open with the remote. CAUSE Coding error in CAS (Car Access System) for trunk locking
Associated Products (33)2013 BMW 535i2013 BMW 550i2013 BMW 740i2013 BMW 740Li2013 BMW 750i2013 BMW 750Li2013 BMW ActiveHybrid 52013 BMW F 800 R2013 BMW R 1200 GS2012 BMW 535i2012 BMW 550i2012 BMW 740i2012 BMW 740Li2012 BMW 750i2012 BMW 750Li2012 BMW 760Li2012 BMW ActiveHybrid 72011 BMW 535i2011 BMW 550i2011 BMW 740i+ 13 moreAssociated Documents - May 1, 2015•Document ID: 10147154Service Bulletin/Repair InstructionsEQUIPMENT; EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM)
- Mfr Comm. #:
- B650915
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryHU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
Associated Products (138)Associated Documents - May 1, 2015•Document ID: 10147143Service Bulletin/Repair InstructionsELECTRICAL SYSTEM
- Mfr Comm. #:
- B610314
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryCheck Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
Associated Products (114)Associated Documents - May 1, 2015•Document ID: 10147136Service Bulletin/Repair InstructionsTIRES:VALVE; WHEELS
- Mfr Comm. #:
- B360215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryValve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
Associated Products (219)Associated Documents - May 1, 2015•Document ID: 10147131Service Bulletin/Repair InstructionsFUEL SYSTEM, GASOLINE
- Mfr Comm. #:
- B130215
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryService Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
Associated Products (89)Associated Documents - May 1, 2015•Document ID: 10147127Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B111614
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
Summary"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Associated Products (56)Associated Documents - May 1, 2015•Document ID: 10147125Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B110815
- Date Added:
- November 5, 2018
- Manufacturer:
- BMW
SummaryN63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Associated Products (91)Associated Documents - April 1, 2015•Document ID: 10152317Service Bulletin/Repair InstructionsBACK OVER PREVENTION
- Mfr Comm. #:
- B660115
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummarySurround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
Associated Products (130)Associated Documents - April 1, 2015•Document ID: 10152303Service Bulletin/Repair InstructionsENGINE
- Mfr Comm. #:
- B121015
- Date Added:
- December 17, 2018
- Manufacturer:
- BMW
SummaryN63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) does not work correctly for the above models with the current version of ISTA/P. After the conversion, the forecast interval does not change to the desired 10,000 miles/12 months, or the forecast is displayed as an invalid value, for example: 25,000 miles/24 months. 1. Incorrect DME coding or calibration data, which is being investigated. 2. The ISTA CBS correction test plan contains an error when attempting to correct an invalid oil service prognosis value.
Associated Products (12)Associated Documents