Mercedes-Benz GLB-Class Service Bulletins (2026)

66 manufacturer communications on file.

• September 26, 2026•Document ID: 11038188

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.10-P-080896

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

  Associated Products (91)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT+ 71 more
  Associated Documents

  • DownloadMC-11038188-0001.pdf↗
• September 22, 2026•Document ID: 11038186

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-078779

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038186-0001.pdf↗
• September 15, 2026•Document ID: 11038174

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-080383

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

  Associated Products (54)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class+ 34 more
  Associated Documents

  • DownloadMC-11038174-0001.pdf↗
• September 14, 2026•Document ID: 11038217

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038217-0001.pdf↗
• August 29, 2026•Document ID: 11037210

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI27.19-P-080869

  Date Added:

  September 9, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Temporary no start condition with check engine light and multiple warning messages. When performing a quick test, the following fault code is stored in Y3/14 ‑ Transmission control for 8‑speed dual‑clutch transmission (DKG): P24F100 The wake‑up line of the control unit has a short circuit to positive. Cause Possible signal timing between EZS control unit and Transmission Control Unit (DKG) Remedy As of 7/15/2026, new SCN coding is available for the EZS control unit. IPR will advise to open a TIPS case for EZS (N73), this is due to GLA models requiring support for SCN coding procedure. GLB (X247) and CLA (118) No TIPS case necessary. 1. SCN coding of EZS Control Unit 2. Clear all faults and perform extended road test with multiple drive cycles GLA (H247) Special function password required. 1. Verify if special procedure Central Locking ‑ Development Data is present in EZS (figure 1) 2. Submit a TIPS case to the Powertrain Inbox with the following information: ‑ Initial Quick Test w/ freeze frame data ‑ IPR Result ‑ DKG Control Unit Log ‑ EZS Control Unit Log ‑ Initial EEPROM data ‑ EZS special procedure menu If the vehicle has had this LI performed and P24F100 has returned, please submit a TIPS case to the Powertrain Inbox.

  Associated Products (20)

  2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class2021 Mercedes-Benz CLA-Class2021 Mercedes-Benz GLA-Class2021 Mercedes-Benz GLB-Class2020 Mercedes-Benz CLA-Class2020 Mercedes-Benz GLB-Class
  Associated Documents

  • DownloadMC-11037210-0001.pdf↗
• August 26, 2026•Document ID: 11036609

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; VISIBILITY/WIPER

  Mfr Comm. #:

  LI54.71-P-080349

  Date Added:

  September 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Frequent rear view camera flap actuations and/or noise associated. NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. Cause Calibration of the reversing camera is in progress. This is not a malfunction, but an intended system behavior. Remedy An optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Open an XSS case requesting addition of the option code "0O1" (Zero, "O", "1"). Once the option code has been added, perform the below based on which option codes the vehicle has. FOR VEHICLES WITH 235 ONLY: 1) Update and SCN code N62/* (PARK Control Unit) 2) Perform verification that optimization is as‑expected as seen below. FOR VEHICLES WITH 235 + 501: 1) Update and SCN code A26/17 (Head Unit) 2) Update and SCN code N62/* (PARK Control Unit) 3) Perform verification that optimization is as‑expected as seen below. IMPORTANT NOTE for vehicles with 235 + 501 ONLY: *For vehicles with 235 only, the "Movable 3D View" is not available due to not having 360 camera feature. Therefore the view was never present.* After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. View PRIOR to SCN Coding: View AFTER SCN Coding: Prior to releasing the vehicle, please verify the following: • Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will re‑open, when calibrating, at 9 MPH. • The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

  Associated Products (6)

  2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class
  Associated Documents

  • DownloadMC-11036609-0001.pdf↗
• August 24, 2026•Document ID: 11036511

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; STRUCTURE:BODY

  Mfr Comm. #:

  LI72.20-P-075746

  Date Added:

  August 31, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.

  Associated Products (97)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class+ 77 more
  Associated Documents

  • DownloadMC-11036511-0001.pdf↗
• August 12, 2026•Document ID: 11036142

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-080132

  Date Added:

  August 12, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

  Associated Products (119)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 99 more
  Associated Documents

  • DownloadMC-11036142-0001.pdf↗
• August 6, 2026•Document ID: 11036101

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  August 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11036101-0001.pdf↗
• July 24, 2026•Document ID: 11035217

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.21-P-080326

  Date Added:

  July 24, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

  Associated Products (47)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class+ 27 more
  Associated Documents

  • DownloadMC-11035217-0001.pdf↗
• July 14, 2026•Document ID: 11035005

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  July 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11035005-0001.pdf↗
• July 8, 2026•Document ID: 11034888

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.60-P-080383

  Date Added:

  July 8, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

  Associated Products (47)

  2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class+ 27 more
  Associated Documents

  • DownloadMC-11034888-0001.pdf↗
• July 2, 2026•Document ID: 11034506

  Service Bulletin/Repair Instructions
  ENGINE; ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.21-P-080326

  Date Added:

  July 6, 2026

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.

  Associated Products (40)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLE-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz CLA-Class+ 20 more
  Associated Documents

  • DownloadMC-11034506-0001.pdf↗
• June 19, 2026•Document ID: 11034064

  Other
  VISIBILITY/WIPER; ENGINE

  Mfr Comm. #:

  PSL-NCU Return Parts 6/19

  Date Added:

  June 25, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 9, 2026. After July 9th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

  Associated Products (82)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz S-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz S-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz S-Class2022 Mercedes-Benz A-Class+ 62 more
  Associated Documents

  • DownloadMC-11034064-0001.pdf↗
• June 12, 2026•Document ID: 11033855

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI00.20-P-080703

  Date Added:

  June 16, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.

  Associated Products (97)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class+ 77 more
  Associated Documents

  • DownloadMC-11033855-0001.pdf↗
• June 2, 2026•Document ID: 11033251

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM; STRUCTURE:BODY

  Mfr Comm. #:

  LI54.71-P-080349

  Date Added:

  June 3, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Frequent rear view camera flap actuations and/or noise associated. NOTE: Rear view camera functions are NOT affected and still perform in accordance with regulatory requirements. Cause Calibration of the reversing camera is in progress. This is not a malfunction, but an intended system behavior. Remedy An optimization has been implemented to reduce the quantity of rearview camera flap actuations for calibration. Open a TIPS case stating "Please add the option code per LI54.71-P-080349 for the Rearview Camera Noise Optimization". Once the option code has been added, perform the below based on which option codes the vehicle has. FOR VEHICLES WITH 235 ONLY: 1) Update and SCN code N62/* (PARK Control Unit) 2) Perform verification that optimization is as-expected as seen below. FOR VEHICLES WITH 235 + 501: 1) Update and SCN code A26/17 (Head Unit) 2) Update and SCN code N62/* (PARK Control Unit) 3) Perform verification that optimization is as-expected as seen below. IMPORTANT NOTE for vehicles with 235 + 501 ONLY: *For vehicles with 235 only, the "Movable 3D View" is not available due to not having 360 camera feature. Therefore the view was never present.* After both control units have been SCN coded, the "Movable 3D View" feature in the head unit will no longer be available. With this change there will be two distinct differences: 1) The "3D" icon when in the top down vehicle view, will no longer be present on the head unit. 2) The digital rendering of the vehicle with the ability to spatially move around the vehicle is no longer possible. This view is replaced with 2D static images of the left and right sides. Prior to releasing the vehicle, please verify the following: • Rear camera flap when calibrating after a key cycle bus sleep will stay open to 29 MPH and then close. Will reopen, when calibrating, at 9 MPH. • The head unit screens mentioned above appear the same as "View AFTER SCN Coding" as shown in the attachment.

  Associated Products (6)

  2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class
  Associated Documents

  • DownloadMC-11033251-0001.pdf↗
• May 26, 2026•Document ID: 11033185

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.85-P-080507

  Date Added:

  June 2, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

  Associated Products (175)

  2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 155 more
  Associated Documents

  • DownloadMC-11033185-0001.pdf↗
• May 22, 2026•Document ID: 11033019

  Service Bulletin/Repair Instructions
  STEERING

  Mfr Comm. #:

  LI46.15-P-070510

  Date Added:

  May 30, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: • Position of height and longitudinal adjustment when the noise occurs • If possible, locate affected component part on steering column • State any change in the noise when steering column component parts are touched (e.g. spring, etc.)

  Associated Products (64)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class+ 44 more
  Associated Documents

  • DownloadMC-11033019-0001.pdf↗
• May 19, 2026•Document ID: 11032875

  Service Bulletin/Repair Instructions
  VISIBILITY/WIPER

  Mfr Comm. #:

  LI82.30-P-059239

  Date Added:

  May 20, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

  Associated Products (221)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class+ 201 more
  Associated Documents

  • DownloadMC-11032875-0001.pdf↗
• May 16, 2026•Document ID: 11032789

  Service Bulletin/Repair Instructions
  SUSPENSION

  Mfr Comm. #:

  LI32.25-P-070053

  Date Added:

  May 20, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint There may be creaking noises when steering while stationary or driving slowly. See Example Noise attachment Cause The vehicle level of the front axle may be too low. The noises when steering can be caused by continuous contact of the end stop buffer with the damper tube. Remedy IMPORTANT: Do not apply document to vehicles outside of the listed validity range. The vehicle level must first be measured using the romess inclinometer (follow WIS instructions!) and the measured values should be compared with the target values in the Wheel Alignment online tool. If the vehicle level is out of tolerance, then the springs on the front axle must be replaced in order to correct the level. The currently installed springs can be pulled up in the XENTRY Parts Information tool through the corresponding selection. How to identify currently installed springs: • Check for colored dots on the front springs. • If no dots or color markings, please check if there is a parts label that is affixed to the spring. If the MB part number is listed, continue with process listed in the paragraph below. • If the part label does not contain an MB part number, is missing or illegible, please check for a barcode label with a 3 digit number. See "Spring Barcode" picture for example. Open a TIPS case with this number and list that it is from the barcode attached to the currently installed spring. • If none of the above references can be found, open a TIPS case. How to identify next spring in line with color dots: • Navigate to the parts catalog and enter the vehicle VIN/FIN. • Navigate to group 32 sub-group 054 (front spring strut) and find the spring. The spring listed in the parts catalog will have a "color marking" indicator. If the dots on the spring and the color listed in the parts catalog is the same then you have the part number of the currently installed spring. If it does not, then you need to clear the vehicle specific filter by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures). Proceed to finding the spring that matches the color dots on the vehicles currently installed spring. • In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. • The spring item numbers are normally listed in sequence (observe and verify valid SA code for vehicle). The next strongest spring is selected by the ascending, next highest item number (Example: If the currently installed spring ends in "13 00" then then next spring in line is "14 00".) How to identify next spring in line with part number tag: • Navigate to the parts catalog and enter the vehicle VIN/FIN and the part number found from the spring. • In order to find the correct or next highest spring, the spring filter must be removed in the XENTRY Parts Information tool. To do this, you need to clear the filters by using the funnel icon on the right side column of the page and clicking "no filter" at the top and then "apply filter" (see "Clear Vehicle EPC Filter" for how-to pictures).

  Associated Products (28)

  2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLB-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLA-Class2022 Mercedes-Benz GLB-Class+ 8 more
  Associated Documents

  • DownloadMC-11032789-0001.pdf↗