Mercedes-Benz CLK-Class Service Bulletins (2010)

31 manufacturer communications on file.

• September 22, 2026•Document ID: 11038186

  Service Bulletin/Repair Instructions
  SERVICE BRAKES

  Mfr Comm. #:

  LI42.10-P-078779

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038186-0001.pdf↗
• September 14, 2026•Document ID: 11038217

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  October 6, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (296)

  2027 Mercedes-Benz C-Class2027 Mercedes-Benz CLA-Class2027 Mercedes-Benz CLE2027 Mercedes-Benz E-Class2027 Mercedes-Benz G-Class2027 Mercedes-Benz GLC-Class2027 Mercedes-Benz GLE-Class2027 Mercedes-Benz S-Class2027 Mercedes-Benz SL-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz G-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class+ 276 more
  Associated Documents

  • DownloadMC-11038217-0001.pdf↗
• August 6, 2026•Document ID: 11036101

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY

  Mfr Comm. #:

  LI82.62-P-078631

  Date Added:

  August 11, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11036101-0001.pdf↗
• July 14, 2026•Document ID: 11035005

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  July 14, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (287)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class+ 267 more
  Associated Documents

  • DownloadMC-11035005-0001.pdf↗
• May 19, 2026•Document ID: 11032875

  Service Bulletin/Repair Instructions
  VISIBILITY/WIPER

  Mfr Comm. #:

  LI82.30-P-059239

  Date Added:

  May 20, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

  Associated Products (221)

  2027 Mercedes-Benz CLA-Class2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz S-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class+ 201 more
  Associated Documents

  • DownloadMC-11032875-0001.pdf↗
• April 16, 2026•Document ID: 11031580

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  April 27, 2026

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

  Associated Products (285)

  2026 Mercedes-Benz AMG GT2026 Mercedes-Benz C-Class2026 Mercedes-Benz CLA-Class2026 Mercedes-Benz CLE2026 Mercedes-Benz E-Class2026 Mercedes-Benz GLA-Class2026 Mercedes-Benz GLB-Class2026 Mercedes-Benz GLC-Class2026 Mercedes-Benz GLE-Class2026 Mercedes-Benz GLS-Class2026 Mercedes-Benz SL-Class2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz CLA-Class2025 Mercedes-Benz CLE2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class+ 265 more
  Associated Documents

  • DownloadMC-11031580-0001.pdf↗
• May 21, 2025•Document ID: 11019018

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI33.30-P-056665

  Date Added:

  June 3, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

  Associated Products (274)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz GLS-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class+ 254 more
  Associated Documents

  • DownloadMC-11019018-0001.pdf↗
• April 28, 2025•Document ID: 11017500

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078896

  Date Added:

  May 2, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

  Associated Products (273)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 253 more
  Associated Documents

  • DownloadMC-11017500-0001.pdf↗
• April 28, 2025•Document ID: 11017496

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  May 2, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

  Associated Products (273)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz C-Class2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz G-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class+ 253 more
  Associated Documents

  • DownloadMC-11017496-0001.pdf↗
• March 5, 2025•Document ID: 11015640

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.70-P-077433

  Date Added:

  March 17, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

  Associated Products (271)

  2025 Mercedes-Benz AMG GT2025 Mercedes-Benz E-Class2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2025 Mercedes-Benz S-Class2025 Mercedes-Benz SL-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class+ 251 more
  Associated Documents

  • DownloadMC-11015640-0001.pdf↗
• February 24, 2025•Document ID: 11014576

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI54.65-P-066284

  Date Added:

  February 28, 2025

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint The flap of the reversing camera opens and closes by itself during forward travel several times during the trip. No camera image is displayed in the head unit. The reversing camera or the 360° system functions normally when activated manually or by engaging drive range "R". Cause This is not a malfunction, but an intended system behavior. Calibration of the reversing camera is in progress. The calibration is completed by: • Opening the camera cover for a maximum of 5 cumulative minutes. • If the vehicle speed is < 35 km/h (<22 MPH). • The steering wheel angle is < 10°. If calibration is aborted by exceeding one of the above conditions, the camera retracts and the calibration will re-attempt once the conditions are achieved and the speed returns to the range of 18 km/h (~11 MPH). Remedy SCN code PARK213M on MFA2 facelift vehicles produced after 09/2024 (A-Class, CLA, GLA, etc...) so the complete calibration speed window is available. For vehicles with PARK213M or PARK223 a calibration is completed successfully by: • Driving forward (typically less than 1 minute). • Vehicle speed is < 35 km/h (<22 MPH). • The steering wheel angle is < 10°. • During daylight. • Without a vehicle following too closely (camera must be able to see asphalt). When calibration has completed successfully, the camera door closes automatically for the rest of the driving cycle. The camera will now only open if the customer requests (Example: Engaging reverse gear). The calibration of the camera will re-initiate every drive cycle (ignition change). The customer can generally perform calibration at the first attempt while briefly maintaining a speed range of 15 km/h (~9 MPH) and 35 km/h (~22 MPH). The customer can therefore play a significant role in reducing the camera door noise and actuation frequency.

  Associated Products (80)

  2025 Mercedes-Benz EQB-Class2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz GLA-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2022 Mercedes-Benz A-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLA-Class2022 Mercedes-Benz EQB-Class2022 Mercedes-Benz GLA-Class+ 60 more
  Associated Documents

  • DownloadMC-11014576-0001.pdf↗
• January 15, 2025•Document ID: 11013332

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI35.30-P-058566

  Date Added:

  January 31, 2025

  Manufacturer:

  MERCEDES BENZ

  Summary

  Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

  Associated Products (158)

  2025 Mercedes-Benz E-Class2025 Mercedes-Benz GLC-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz C-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz GLC-Class2023 Mercedes-Benz GLE-Class2023 Mercedes-Benz GLS-Class2023 Mercedes-Benz S-Class2023 Mercedes-Benz SL-Class2022 Mercedes-Benz C-Class2022 Mercedes-Benz CLS-Class+ 138 more
  Associated Documents

  • DownloadMC-11013332-0001.pdf↗
• October 23, 2024•Document ID: 11009122

  Service Bulletin/Repair Instructions
  STRUCTURE:BODY; VISIBILITY/WIPER

  Mfr Comm. #:

  LI82.35-P-078467

  Date Added:

  October 25, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

  Associated Products (265)

  2025 Mercedes-Benz GLA-Class2025 Mercedes-Benz GLB-Class2025 Mercedes-Benz GLE-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class+ 245 more
  Associated Documents

  • DownloadMC-11009122-0001.pdf↗
• September 28, 2024•Document ID: 11008091

  Service Bulletin/Repair Instructions
  ELECTRICAL SYSTEM

  Mfr Comm. #:

  LI82.70-P-077433

  Date Added:

  September 28, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11008091-0001.pdf↗
• September 21, 2024•Document ID: 11007974

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078307

  Date Added:

  September 24, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11007974-0001.pdf↗
• September 10, 2024•Document ID: 11007753

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078301

  Date Added:

  September 13, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11007753-0001.pdf↗
• July 23, 2024•Document ID: 11005294

  Service Bulletin/Repair Instructions
  EXTERIOR LIGHTING

  Mfr Comm. #:

  LI82.10-P-078069

  Date Added:

  July 27, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

  Associated Products (263)

  2025 Mercedes-Benz GLA-Class2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz CLE2024 Mercedes-Benz E-Class2024 Mercedes-Benz EQB-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class+ 243 more
  Associated Documents

  • DownloadMC-11005294-0001.pdf↗
• December 4, 2023•Document ID: 10248162

  Service Bulletin/Repair Instructions
  SEATS

  Mfr Comm. #:

  LI91.18-P-077075

  Date Added:

  January 3, 2024

  Manufacturer:

  MERCEDES-BENZ

  Summary

  Crease formation on genuine leather seat covers in vehicles with low mileage • Objects left on the seats for extended periods of time (pressure marks). • Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). • Light initial creases due to vehicle handling. • Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!

  Associated Products (241)

  2024 Mercedes-Benz AMG GT2024 Mercedes-Benz C-Class2024 Mercedes-Benz CLA-Class2024 Mercedes-Benz E-Class2024 Mercedes-Benz G-Class2024 Mercedes-Benz GLA-Class2024 Mercedes-Benz GLB-Class2024 Mercedes-Benz GLC-Class2024 Mercedes-Benz GLE-Class2024 Mercedes-Benz GLS-Class2024 Mercedes-Benz S-Class2024 Mercedes-Benz SL-Class2023 Mercedes-Benz AMG GT2023 Mercedes-Benz C-Class2023 Mercedes-Benz CLA-Class2023 Mercedes-Benz CLE2023 Mercedes-Benz CLS-Class2023 Mercedes-Benz E-Class2023 Mercedes-Benz EQB-Class2023 Mercedes-Benz G-Class+ 221 more
  Associated Documents

  • DownloadMC-10248162-0001.pdf↗
• September 30, 2020•Document ID: 10181124

  Service Bulletin/Repair Instructions
  POWER TRAIN

  Mfr Comm. #:

  LI27.50-P-071658

  Date Added:

  October 19, 2020

  Manufacturer:

  MERCEDES BENZ

  Summary

  Harsh engagement when changing gear range from P to D or R

  Associated Products (27)

  2013 Mercedes-Benz S-Class2013 Mercedes-Benz SL-Class2012 Mercedes-Benz S-Class2011 Mercedes-Benz C-Class2011 Mercedes-Benz CL-Class2011 Mercedes-Benz E-Class2011 Mercedes-Benz S-Class2011 Mercedes-Benz SL-Class2010 Mercedes-Benz C-Class2010 Mercedes-Benz CL-Class2010 Mercedes-Benz CLK-Class2010 Mercedes-Benz E-Class2010 Mercedes-Benz S-Class2009 Mercedes-Benz E-Class2008 Mercedes-Benz E-Class2007 Mercedes-Benz E-Class2006 Mercedes-Benz C-Class2006 Mercedes-Benz E-Class2005 Mercedes-Benz C-Class2005 Mercedes-Benz E-Class+ 7 more
  Associated Documents

  • DownloadMC-10181124-0001.pdf↗
• May 21, 2020•Document ID: 10176670

  Service Bulletin/Repair Instructions
  EQUIPMENT

  Mfr Comm. #:

  NCU - HVAC Warra

  Date Added:

  June 22, 2020

  Manufacturer:

  MERCEDES-BENZ

  Summary

  To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters

  Associated Products (113)

  2017 Mercedes-Benz AMG GT2017 Mercedes-Benz B-Class2017 Mercedes-Benz C-Class2017 Mercedes-Benz CLA-Class2017 Mercedes-Benz CLS-Class2017 Mercedes-Benz E-Class2017 Mercedes-Benz G-Class2017 Mercedes-Benz GLA-Class2017 Mercedes-Benz GLC-Class2017 Mercedes-Benz GL-Class2017 Mercedes-Benz GLE-Class2017 Mercedes-Benz GLS-Class2017 Mercedes-Benz S-Class2017 Mercedes-Benz SLC-Class2017 Mercedes-Benz SL-Class2017 Mercedes-Benz SLK-Class2016 Mercedes-Benz AMG GT2016 Mercedes-Benz B-Class2016 Mercedes-Benz C-Class2016 Mercedes-Benz CLA-Class+ 93 more
  Associated Documents

  • DownloadMC-10176670-0001.pdf↗