BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.
BMW North America, LLC (BMW) is recalling certain model year 2012-2015 320i, 320xi, 328i, 328xi, 335i, 335xi, and ActiveHybrid3 vehicles manufactured October 20, 2011, to June 22, 2015, 2014-2015 328xi Sports Wagon vehicles manufactured March 21, 2013, to March 17, 2015, 2014-2015 328d, 328xd vehicles manufactured June 28, 2013, to April 21, 2015, and 2014-2015 328xd Sports Wagon vehicles manufactured July 5, 2013, to April 21, 2015. The affected vehicles may have been programmed with new software that inadvertently makes the front side marker lights inoperative in conjunction with the parking lights or the headlights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Everything looks good
No injuries · No fire · No crash
On XXX, while driving on Interstate XXX with my family near [XXX], the engine shut off and the vehicle lost all power. The event was preceded by a "Reduced Power" error displayed on the dashboard. Traffic was moderate and I was able to pull over to the right shoulder. The engine shutting off while on an interstate highway is obviously quite dangerous. After waiting for a few minutes I was able to restart the car and continue travel. I took my vehicle to a mechanic and several potentially relevant codes were found: 110001: Cylinder injection shutdown: pressure too low in high pressure system 11A002: Fuel high pressure, plausibility: pressure too low 481B03: EKPS control current too low Review of the issue and codes with the mechanic and internet forums indicates the fuel pump control module (EKPS) is failing. This can be exacerbated by hot weather. A failing EKPS can cause sudden stalling at any time, including at highway speeds, making the vehicle unsafe to drive until repaired. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
No injuries · No fire · No crash
The engine intake tract, PCV infrastructure, and the main lower engine wiring harness loom failed due to improper reassembly during Federal Safety Recall 24V-608. The technician left the main intake coupler completely loose and spinning freely by hand, and left the MAF sensor crooked. This introduced a massive unmetered air leak and severe vacuum leaks. Simultaneously, the technician over-tensioned, pinched, or damaged the Cylinder 2 wiring loom components. The vehicle is currently parked dead and untouched at my residence, and it is 100% available for immediate federal or corporate inspection.The unsealed intake tract and damaged wiring harness caused the engine to run dangerously lean at highway speeds. This resulted in sudden, violent engine shuttering, rapid deceleration, severe mechanical engine knocking, and a terminal Cylinder 2 misfire. This component failure caused an immediate loss of vehicle propulsion on a high-speed public highway, creating an extreme risk of a high-speed collision and leaving the vehicle completely disabled. The issue has not yet been physically inspected by a third party because the vehicle is unsafe to drive. I went to the originating dealer (BMW of Henderson) in person on July 16, 2026, to coordinate a safety re-inspection under an active BMW North America Corporate Case. Dealership management actively obstructed the safety process, gave technically impossible justifications regarding the recall execution, and flatly refused to dispatch a complimentary flatbed tow. They attempted to hold the safety re-inspection hostage behind out-of-pocket customer towing costs and upfront retail diagnostic fees. There were 0 mechanical warnings or symptoms prior to the recall. The vehicle was meticulously maintained with 5,000-mile oil changes and a perfectly tight timing chain. The severe drivetrain malfunction warnings, violent front-end shaking, and terminal engine knocking appeared after picking up my car.
No injuries · No fire · No crash
The contact owns a 2015 BMW 328I. The contact stated that while driving at 40 MPH, the vehicle caught on fire. The fire originated in the engine compartment. There were no warning lights illuminated. The driver was able to extinguish the fire. The vehicle was towed to the residence and was then towed to an independent mechanic, but the vehicle was not diagnosed or repaired. The vehicle was towed to the local dealer, where it was diagnosed with an electrical short circuit in the front water pump connector. The vehicle was not repaired. The contact associated the failure with NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The manufacturer was notified of the failure, and a claim was opened. The failure mileage was approximately 110,000.
On [XXX], my 2015 BMW 328i xDrive (VIN: [XXX] , N20 engine, 124,250 miles) suffered a catastrophic engine failure while in operation. Component/System Failed: The timing chain guides and oil pump drive chain module failed. The plastic timing chain guide broke apart inside the engine. The vehicle was salvaged and is no longer available for inspection. Safety Risk: The oil pressure warning illuminated suddenly while driving at highway speed with no prior warning. Sudden loss of oil pressure and engine power while operating a vehicle at speed creates a significant risk of accident, loss of vehicle control, and injury to the driver and others on the road. Confirmed by Service Center: BMW of Springfield, New Jersey performed a formal diagnostic confirming timing chain guide failure and oil pump drive chain failure. A BMW mechanic performed a scope inspection on April 3, 2026 visually confirming the broken plastic timing chain guide. Repair estimate: $7,191.42. Inspected by Others: The vehicle was inspected solely by BMW of Springfield. No police, insurance, or manufacturer representatives conducted a separate inspection. The failure mode is consistent with the defect acknowledged in BMW NA Technical Service Bulletin SI B11 03 17 and federal class action [XXX] v. BMW of North America, LLC (D.N.J. [XXX]). Warning Symptoms: The only warning was a sudden oil pressure warning message on the dashboard immediately before failure. Prior to that moment the vehicle operated normally with no unusual noises, no warning lights, and no fluid leaks. There were no gradual symptoms or prior indications of impending failure. Vehicle was declared a total economic loss and salvaged for $1,650.00. No injuries occurred. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
No injuries · No fire · No crash